Related Manuals for OxyGo CPAP Sanitizer+
Summary of Contents for OxyGo CPAP Sanitizer+
- Page 1 P r o d u c t I n s t r u c t i o n s C l e a n s a n d s a n i t i z e s s o y o u c a n k e e p g o i n g . w w w .
- Page 2 DEVICE To protect against risk of electrical shock, do no immerse cord, plug, power adapter, or the OxyGo CPAP Sanitizer+ device in water or other liquid. Do NOT operate appliance if the power cord or plug is damaged. Any damaged part must be repaired or replaced by the manufacturer or an authorized service provider before use.
- Page 3 Please carefully review the operation and safety information for the OxyGo CPAP Sanitizer+ and follow all recommendations. Use of this product in a manner other than described in these product instructions or specified by the manufacturer may hinder safety protection provided by this equipment.
-
Page 4: Table Of Contents
T a b l e o f C o n t e n t s Items included ..............4 Key Parts ..............5 Menu Panel ...............6 Operating Instructions ..............7 Setting Clock ..............7 Open/Close Lid ..............7 Manual Mode Settings ..............8 UV-C sanitizing in manual mode ..............8 Activated Oxygen sanitizing in ..............9... -
Page 5: Items Included
W h a t c o m e s w i t h y o u r O x y G o C P A P S a n i t i z e r + ? OxyGo CPAP Sanitizer+ Device 1700-5010... -
Page 6: Key Parts
K e y P a r t s DC Input 4. Open button 2. Activated carbon filter 5. External sealing lid 3. UV Light 6. Internal sealing lid... -
Page 7: Menu Panel
M e n u P a n e l R e m a i n i n g M i n T i m e r S a n i t i z i n g . . . S t a r t / P a u s e D o w n M a n u a l T i m e r... -
Page 8: Operating Instructions
Once the display has flashed 4 times the adjusted minute will be saved. This completes clock set-up. Opening and closing the lid Note: When opening and closing the lid of the OxyGo CPAP Sanitizer+, place hands on the sides or front of the lid to avoid unintentionally changing any settings. -
Page 9: Manual Mode Settings
Once all items to be sanitized are inside the chamber, close the lid of the OxyGo CPAP Sanitizer+. Press the Start/Pause button on the lid of the OxyGo CPAP Sanitizer+ to turn the device on. Press the manual button to change the desired mode. Press the manual button until the UV symbol is shown in the upper right corner of the display. -
Page 10: Activated Oxygen Sanitizing In Manual Mode
To perform Activated Oxygen sanitizing ONLY follow these instructions. Open the lid of the OxyGo CPAP Sanitizer+ by pushing the large OPEN button on the front of the device. Open the blue internal sealing lid inside the chamber by lifting and partially rotating it counterclockwise. - Page 11 10. When the cycle is completed 4 dashes will appear on the screen to show that the cycle is complete. 11. After the cycle is completed allow the OxyGo CPAP Sanitizer+ sit for 2 hours for the Activated Oxygen to dissipate prior to opening.
-
Page 12: In Manual Mode
To perform UV & Activated Oxygen disinfecting follow these instructions. Open the lid of the OxyGo CPAP Sanitizer+ by pushing the large OPEN button on the front of the device. Open the blue internal sealing lid inside of the chamber by lifting and partially rotating it counterclockwise. -
Page 13: Auto Mode Settings
A u t o M o d e S e t t i n g s How to set the sanitizing mode using the timer To set the timer on the OxyGo CPAP Sanitizer+ for the device to start automatically at a specified time follow these instructions. -
Page 14: Replacing Carbon Filters
1. The first filter is located in the lower left corner of the bottom inside the chamber. It is round with many small holes in it. The OxyGo CPAP Sanitizer+ device comes with six replacement filters. Additional replacement filters are available through your provider of the device. -
Page 15: Routine Care
1. Do not expose the OxyGo CPAP Sanitizer+ device to damp environments. 2. Do not expose the OxyGo CPAP Sanitizer+ to sunlight or direct heat for extended periods of time. 3. When using the product place it in a clean, dry, well-ventilated area. - Page 16 The OxyGo CPAP Sanitizer+ produces Activated Oxygen by taking in room air and converting it to Activated Oxygen (O3) for the sanitizing process.
- Page 17 UV light exposure. Do I need to continue washing my sleep equipment if I am using the OxyGo CPAP Sanitizer frequently? The UV and Activated Oxygen modes in the OxyGo CPAP Sanitizer+ will not remove facial oils, makeup, lotions, or other organic materials that may build up on your equipment.
- Page 18 Are there any parts I need to routinely replace in my OxyGo CPAP Sanitizer+? Yes. The Activated Carbon Filter located inside the chamber is recommended to be replaced every two months with daily use. Your unit comes with six additional filters providing six month's supply of replacement filters.
- Page 19 For questions or service on your OxyGo CPAP Sanitizer+, please contact your local equipment provider. For warranty information visit www.oxygo.life/sanitizer-warranty.
- Page 20 . o x y g o . l i f e For questions or service on your OxyGo CPAP Sanitizer+, please contact your local Equipment Provider. For warranty information visit www.oxygo.life/sanitizer-warranty. PN 1700-5051 V3 © 2021 OxyGo HQ Florida, LLC. All rights reserved.
Need help?
Do you have a question about the CPAP Sanitizer+ and is the answer not in the manual?
Questions and answers