Download
Share
Print this page
Atten AT-R1816 User Manual
  1. Manuals
  2. Brands
  3. Atten Manuals
  4. Oven
  5. AT-R1816
  6. User manual

Atten AT-R1816 User Manual

Infrared reflow oven
Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the AT-R1816 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Atten AT-R1816

  • Page 2: Table Of Contents

    Contents Introduction……………………………………………………......3 Main technique parameter……………………………………......4 Structure introduction………………………………………......5 Function key introduction………………………………………………..…..6 The function of temperature curve………………………………………..6-8 Common alloy solder temperature curve adjustment parameters…………..9 Common alloy solder physical constant and characteristics……………..…..10 Running operation……………………………………………………...…11-19 Back soldering operation………………………………………………….19-20 Faults alarm……………………………………………………………….20-22 Attentions………………………………………………..……………….…..22 Parameters of the fixed curves …………...……..…………………………...23...

  • Page 3: Introduction

    AT-R1816 can make a temperature control curve to match the request of the SMD production technique completely. The “temperature control curve” of the AT-R1816 can be adjusted accurately, so it can be used for many kinds of soldering paste which all have different material properties. It can shut down automatically when there is a alarm or any faults.

  • Page 4: Main Technique Parameter

    Main technique parameter 、 Working voltage: AC220V(AC110V order) 、 Working frequency:50-60Hz 、 Maximum output power: 600W 、 Heating methods: infrared radiation and hot air mix heating 、 Operating system: Chinese-English operating system 、 Working mode: automatic soldering mode, maintenance mode adjustable 、...
  • Page 7 2. The purpose and role of the heating Activated the liquid flux of tin pulp; under the role of the liquid flux remove the oxide of surface components inside the tin pulp; preparation for soldering. In this section the temperature of the lead alloy solder and precious metal alloy solder should be set (150 ~180 ).
  • Page 8 center of the solder pad have the role of reform automatically. Also in the humid of the solder flux the solder tin and surface metal of components formed alloy layer infiltrated into components structural organization, which form the ideal soldering structural. Setting the time about (10~30s), a large area and the larger components shade of PCB should be set much longer time.
  • Page 9 Common alloy solder temperature curve adjustment parameters Warm-up Heating Soldering Keep Cool Solder Type Proportion /1min /1min /30s Low-temperature Sn43-Pb43- 100-120 130-150 200-210 ,leaded Bi14 Lead-free low Sn42-Bi58 100-120 120-130 180-200 temperature Lead-free low Sn48-In52 100-120 120-130 180-200 temperature Lead, mid- Sn63-Pb37 130-150 170-180...

  • Page 10: Common Alloy Solder Physical Constant And Characteristics

    Common alloy solder physical constant and characteristics Melting Solder Alloy temperat Mechanical properties conductiv Push Liquidus Elongati rigidity Strength Pb Ag Sb Bi Au Cu Zn （ （ （ （ ℃ ℃ ℃ ℃ ） ） ） ） （ （ （ （ ）...

  • Page 11: Running Operation

    Running operation There are two working mode to select in this equipment, which are "Solder" and "Repair". The mode “Solder” is designed to solder the circuit board components, the whole process are “PREH” (warm-up), “HEAT” “SLDR” “KEEP” “COOL” (heating), (solder), (heat preservation) and (wait for the machine to cool down);...
  • Page 12 figure 5, the display shows the language and the display mode, You can press Fig5 system setting Fig6 Curve selection the key “ ” or “ ” to select it, press the key “SET” to make sure your change, and press the key “RUN”...
  • Page 13 select segment you want to setting. Press the key “RUN” returns back the standby menu, and press the key “SET” to enter the temperature setting state. As shown in figure 5. Except the displayed, the mode of the graphics display and Note: the text display are the same.
  • Page 14 Fig9 Text Temperature settings Fig10 Curve Temperature settings Fig 11 Text Time Settings Fig 12 Curve Time Settings...
  • Page 15 Setting parameter of segment “HEAT” ※ As shown in “Fig 13” 、 、 、 、 “ “ “ “ Fig 14”press the key “ ” select the heating segment, the screen display “HEAT”, press the key “SET” enter the 、 、 、 、 “ temperature setting state.
  • Page 16 Fig 15 Text Temperature settings Fig 16 Curve Temperature settings Fig 17 Text Time Settings Fig 18 Curve Time Settings Setting parameter of segment “SLDR ” Under the interface in “Fig19” 、 “ “ “ “ Fig20” 、 、 、 、 “ “ “ “ Fig21”...
  • Page 17 Fig 21 Text Temperature settings Fig 22 Curve Temperature settings Fig 23 Text Time Settings Fig 24 Curve Time Settings ※ Setting parameter of segment “KEEP” 、 、 、 、 “ “ “ “ 、 、 、 、 “ “ “ “ 、...
  • Page 18 Fig 27 Text Temperature settings Fig 28 Curve Temperature settings Setting parameter of segment “COOL” ※ 、 “ “ “ “ 、 、 、 、 “ “ “ “ 、 、 、 、 “ “ “ “ Under the interface in “Fig29” F ig30”...
  • Page 19 Fig 31 Text Temperature settings Fig 32 Curve Temperature settings Setting parameter of repair mode Under the interface of standby as shown in , “Fig 33” 、 、 、 、 “ “ “ “ F ig 34” 、 、 、 、 “ “ “ “ F ig 35”...

  • Page 20: Back Soldering Operation

    Fig 35Text Temperature settings Fig 36Curve Temperature settings Fig 37Text Time Settings Fig 38Curve Time Settings On the setting the mode, if the machine have nothing operate it NOTE: will return back to the standby state; on the standby state, the machine have nothing operate over 30Min will shut down automatically.

  • Page 21: Faults Alarm

    When the machine is running you want to exit please press the key “RUN”. You also can press the key “RUN” to stop exhaust and return to standby mode. Fig 39Text Operation Fig 40Curve Operation When the machine running to cooling segment, fan starts and full exhaust.
  • Page 22 Fig41Text Dangerous Temperature! Fig42Curve DangerousTemperature! 2. Failure of detecting element When there is something wrong of the temperature-detecting element, the “Detecting Element!” as shown in “Fig 43” 、 、 、 、 “ “ “ “ F ig 44”; the screen displayed machine alarm and the fan start to work.

  • Page 23: Attentions

    8. Don’t stretch your hand into the cabinet when the machine has not fall to the safe temperature. 9. Don’t use the machine on tablecloth, to prevent plug up the air intake. 10. If the heat pipe damaged, must replace it with the same manufacturer production. WWW.ATTEN.EU INFO@ATTEN.EU +31 653 454 999...