J&J Electronics PureWhite 2 Installation And Operation Manual

TM
PureWhite 2 Pool Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL LAMPS
Model #s: LPL-P2-WHT-12, LPL-P2-WHT-120, LPL-P2-WHT-12-SQ, LPL-P2-WHT-120-SQ
PureWhite Replacement LED In-Ground Pool lamps offer superior, bright white illumination for your pool. This owner's manual contains important information
on installing and using your new PureWhite Replacement LED In-Ground Pool Lamp. Please read it carefully and keep it in a safe place for future reference.
WARNING! This device is not intended for use with
emergency exit fixtures or emergency exit lights.
WARNING! Permanent damage to the low voltage 14VAC
lamp will occur if installed on a 120VAC circuit.
PureWhite Replacement LED In-Ground Pool lamps are available in 14VAC (low
voltage) and 120VAC models as indicated on the product packaging. Each lamp has
a screw-in Edison base.
WARNING! Remove warning label from PureWhite lens
before installation.
The warning label is placed on top of a special optical diffuser designed to maximize
the light projection of the PureWhite lamp. When you remove the label, a protective film
will come off with it. Once the warning label and protective film have been removed,
do not allow the diffuser decal underneath to be scratched.
ATTENTION 14V PUREWHITE OWNERS!
A socket voltage range of 13.5 – 15.0 will achieve optimal brightness. To verify the
voltage, at the lamp socket, measure the open circuit voltage (no lamp in the socket).
Set the transformer tap to 14.0VAC.
DANGER!
Risk of electrical shock or electrocution
Always disconnect power to the pool light at the circuit breaker panel before
attempting to service the lamp. Failure to do so could result in serious injury or death
due to electrical shock. Refer to the original manufacturer's pool light installation
manual before proceeding. As with any electrical device, installation and service
should always be performed by a qualified individual. This device is not intended for
use in anything other than in-ground pools.
Rated Lamp Life
The illumination generated by the PureWhite Replacement LED In-Ground Pool lamp is
based on Light Emitting Diode (LED) technology. The average expected lamp life is
rated up to 50,000 elapsed time hours under normal operating conditions.
[Temperature: 33°F to 95°F (1°C to 35°C), Humidity: 0-95% non-condensing].
Safety Precautions
•
Do not open, service or tamper with any internal component of the PureWhite
Replacement LED In-Ground Pool lamp. Doing so will void the warranty. Follow
each instruction in this owner's manual and pay careful attention to all warnings.
•
Do not directly expose or immerse the PureWhite Replacement LED In-Ground
Pool lamp in water without containing it in a proper, watertight, NRTL
(nationally recognized testing laboratory) pool light housing and niche
assembly.
•
Keep the pool light housing dry.
•
Handle the PureWhite Replacement LED In-Ground Pool lamp with care. Be
careful not to drop the unit.
IMPORTANT NOTE:
PureWhite lamps are recommended for installation by a qualified pool professional.
Installation
The installation steps in this owner's manual are intended as guidelines. For specific
instructions on how to replace a pool lamp, please refer to the original manufacturer's
pool light installation manual before proceeding.
Light housing compatibility
LPL-P2-WHT-12, LPL-P2-WHT-120, LPL-P2-WHT-12-SQ, LPL-P2-WHT-120-SQ
PureWhite Replacement LED In-Ground Pool lamps must be installed in a compatible
NRTL pool light housing.
•
J&J Electronics 6 Bendix, Irvine, CA 92618 USA
Compatible NRTL light housings
include:
®
Hayward Astrolite ™ SP058 Series
®
Pentair Amerlite 784 Series
®
™
Jacuzzi Full Moon
®
Sta-Rite SwimQuip ™ Series 0508
Gasket compatibility
®
Hayward Astrolite ™ SP058 Series Housing -
Use replacement gasket specified by manufacturer.
®
Pentair Amerlite 784 Series -
Included with LPL-P2-WHT-12 and LPL-P2-WHT-120.
®
Jacuzzi Full Moon ™ -
Use replacement gasket specified by manufacturer.
®
™
Sta-Rite SwimQuip ™ Series 0508 -
#LPL-G-S. Included with LPL-P2-WHT-12-SQ and LPL-P2-WHT-120-SQ.
The product warranty is voided if the proper gasket is not installed.
See the "Warranty" section at the end of this manual for details.
WARNING!
Read this before attempting installation
Your PureWhite lamp is not an ordinary light bulb. It is a valuable electronic device that
is not designed to come in direct contact with water. An improper installation that
results in water leakage into the pool light housing can permanently damage the
PureWhite lamp. Please read these installation steps and the original
manufacturer's pool light installation manual carefully before proceeding.
STEP 1
Remove light housing from niche
Make sure power to the pool light is turned off at the circuit breaker. Carefully remove
the existing light housing from the niche assembly and place it on the pool deck. There
should be enough power cord to do this easily. If there is not enough power cord to
allow the light housing to reach the pool deck surface, call your local pool service
company.
WARNING! Verify that your PureWhite lamp voltage rating
(120VAC or 14VAC) matches your electrical system's
voltage requirements before proceeding with installation.
STEP 2
Remove old lamp
Access the old lamp according to the original manufacturer's pool light installation
manual. Remove the screws and/or loosen the clamp that holds the face plate and lens
in place. Carefully remove the lens from the pool light housing. Take care not to
damage the surface of the light housing body that makes contact with the rubber
gasket.
• •
949.455.4460
800.735.4553
Figure 1: LPL-P2-WHT
Requires installation of J&J Gasket #LPL-G-P.
Requires installation of J&J Gasket
•
www.jandjpoolspa.com
PAGE 1