Advertisement

Quick Links

Congratulations on your purchase of the
VORTEX MOBILE CLEANING UNIT.
This instruction/parts manual is a guide for
operating and servicing your BLUELINE
VORTEX 7000HHP
Proper operation and service are necessary to
ensure the outstanding performance of this unit.
When properly maintained, your mobile cleaning
unit will have a long and trouble-free life.
The following service methods outlined in this
manual are detailed in a manner that operation and
servicing may be performed properly and safely.
Because service levels vary due to the skill of the
mechanic, tools and parts availability, ensure that
prior to attempting any repair, you are familiar with
this equipment and have the proper tools. Any
questions regarding the operation, service, or repair
of this unit should be directed to your nearest
BLUELINE dealer.
The headings WARNING and CAUTION are
utilized to warn you that steps must be taken to
prevent personal injury or damage to the
equipment. Please make sure that you have read
and understand these instructions entirely before
proceeding with the operation of this unit.
BLUELINE VORTEX 7000HHP
mobile cleaning unit.
®
Record your units vehicle identification number
here for future reference or if you should need to
contact the factory in the future for any reason.
VIN:
This service and operations manual is written
specifically for BLUELINE VORTEX 7000HHP
mobile cleaning unit manufactured by:
BLUELINE EQUIPMENT LLC
2604 Liberator Drive
Prescott, AZ 86301
The information contained in this document is
subject to change without notice and does not
represent a commitment on the part of BLUELINE
EQUIPMENT LLC.
All rights reserved. Copyright 2006 by
BLUELINE EQUIPMENT LLC. No part of this
work may be used or reproduced in any form or
means without the express written consent and
permission of BLUELINE EQUIPMENT LLC.
Published by BLUELINE EQUIPMENT LLC.
First printing: October 2007
Printed in USA
VORTEX 7000HHP
PART# 49-034
INTRODUCTION
USA
MANUAL
®
October, 07
I
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VORTEX 7000HHP and is the answer not in the manual?

Questions and answers

Summary of Contents for BlueLine VORTEX 7000HHP

  • Page 1 Any subject to change without notice and does not questions regarding the operation, service, or repair represent a commitment on the part of BLUELINE of this unit should be directed to your nearest EQUIPMENT LLC.
  • Page 2 If BLUELINE receives notice of any defects during the warranty period, BLUELINE will either, at its option, repair or replace products that prove to be defective. Any transportation, related service labor, normal maintenance and diagnostic calls are not included.
  • Page 3: Table Of Contents

    Pump, Operation, Cleaning, Upholstery Cleaning, Stair Tool Cleaning, Flood Restoration, Shut Down and Daily Maintenance, Freeze Protection. SECTION THREE: MAINTENANCE and SERVICE MAINTENANCE CHART 5. MAINTENANCE 6. GENERAL SERVICE ADJUSTMENTS 7. TROUBLESHOOTING SECTION FOUR: PARTS and ACCESSORIES 9. ILLUSTRATED PARTS LISTINGS 10. ACCESSORIES BLUELINE VORTEX 7000HHP...
  • Page 5 SECTION 1: GENERAL INFORMATION 1. SAFETY Safety Specifications Chemical requirements Water requirements 2. RECEIVING YOUR TRUCK MOUNT UNIT Dealer responsibility Acceptance of shipment Equipment listing Optional equipment BLUELINE VORTEX 7000HHP...
  • Page 6: Safety

    SECTION 1 1. SAFETY For Your Safety! The following WARNING labels are on your VORTEX 7000HHP mobile cleaning unit. ® These labels point out important Warnings and Cautions, which must be followed at all times. Failure to follow warnings could result in personal injury, fatality, to yourself and/or others or property damage.
  • Page 7 20 minutes after the unit is temperatures. Improper use could result in shut off. Severe burns could result. serious injury or fatality. 8. Water under high pressure at high temperature can cause burns, severe BLUELINE VORTEX 7000HHP...
  • Page 8 Any modification could result in serious injury or fatality, and will void your warranty. 16. California Proposition 65 Warning: Engine exhaust from this product contains chemicals known by the State of California to cause cancer, birth defects, or other reproductive harm. 4 BLUELINE VORTEX 7000HHP...
  • Page 9 220 Gallons. Waste Recovery 110 Gallons JET SIZING BLUELINE recommends that the total floor tool tip size does not exceed .06”. Using larger jet sizes on your VORTEX 7000HHP unit may reduce cleaning temperatures. ® Example: Four-jet wand uses four 95015 jets. (95 deg. Spray angle w/015 orifice) .015 x 4 = .06...
  • Page 10 Because hard water deposits will damage the plumbing and heat exchange systems on this unit, THE BLUELINE DEALER THAT YOU BLUELINE recommends that a high quality water PURCHASED THIS MOBILE TRUCK softener be used in areas where the water hardness CLEANING UNIT FROM IS RESPONSIBLE exceeds 3-1/2 grains.
  • Page 11 H. 2 Chemical solution reels. I. 400 ft. of 1/4 in. high pressure solution hose with quick connects J. 2 vacuum hose connectors K. 50 ft. water supply hose with quick connect L. Vortex marketing materials package. OPTIONAL EQUIPMENT BLUELINE VORTEX 7000HHP...
  • Page 12 Vacuum system Chemical pumping system 4. OPERATION Preparation Starting the unit Priming the chemical pump Automatic waste pump Operation Automatic Diverter System Cleaning Upholstery cleaning Stair tool cleaning Flood restoration/extraction Shut down and daily maintenance Freeze protection 8 BLUELINE VORTEX 7000HHP...
  • Page 13 SECTION 2 BLUELINE VORTEX 7000HHP...
  • Page 14 SECTION 2 BATTERY CONNECTION FIRE EXTINGUISHER BLUELINE, and many government agencies, recommend that a fire extinguisher rated for A, B, Explosive gases, Dangerous gases! and C type fires be installed into any commercial Batteries contain sulfuric acid. To prevent acid vehicle.
  • Page 15: Systems

    The low water level switch located on the water tank will automatically shut off the water pump clutch, disengaging the water pump when the fresh water supply is low. BLUELINE VORTEX 7000HHP...
  • Page 16 SECTION 2 Water System 12 BLUELINE VORTEX 7000HHP...
  • Page 17 Note: Waste tank level shut off sensor vacuum pump relief valve is installed for vacuum will not shut the unit off due to high levels of pump protection. foam. The use of a quality defoamer is recommended. BLUELINE VORTEX 7000HHP...
  • Page 18 The chemicals then flow into the stainless steel pulsation chemical pump. The chemical pump injects the chemicals to the three way selector valve located on the front panel. This valve may be used to turn the chemical flow to PRIME, OFF, or METER. 14 BLUELINE VORTEX 7000HHP...
  • Page 19: Operation

    This section of the operator’s manual explains how to prepare, start, operate, shut down and maintain your BLUELINE VORTEX 7000HHP mobile ® cleaning unit. The VORTEX 7000HHP unit is ® easy to operate, however only trained operators should proceed. Operate this unit and equipment only in a well ventilated area.
  • Page 20 SECTION 2 16 BLUELINE VORTEX 7000HHP...
  • Page 21 Connect the hose to the further use. faucet. Turn the water supply faucet on. Fill BLUELINE VORTEX 7000HHP...
  • Page 22 Connect the vacuum hose(s) to the vacuum Inspect all tools and equipment. Clean repair inlet connection(s) on the side of the box and or replace as needed. truck. Connect the opposite end of the vacuum hose(s) to the cleaning tool(s). 18 BLUELINE VORTEX 7000HHP...
  • Page 23 .015 x 4 = .06 it is released it displays the oil temperature. When using two wands while cleaning with this unit, BLUELINE recommends that the tip size in each tool does not exceed a total of “.04”. Example: Four jet wand uses four 9501 jets.
  • Page 24 The chemical will then flow from the to the water pump clutch may occur. chemical jug through the chemical prime tube. NOTE: BLUELINE recommends that the If the pump does not prime, then: chemical pump be primed whenever the Place the chemical prime tube into the water pump is on.
  • Page 25 UPHOLSTERY CLEANING AUTOMATIC DIVERTER SYSTEM 1. Upholstery tools have a lower flow rate and smaller orifices. Set the temperature control Your VORTEX 7000HHP mobile cleaning ® to the desired setting. To maintain proper unit is equipped with an automatic diverter cleaning temperatures, make certain that the control system.
  • Page 26 Clean out any debris and re-install. 180 deg. F. This will also help to remove any excess moisture from the vacuum pump. NOTE: Damage may occur to the vacuum pump if strainer basket is damaged or improperly installed. 22 BLUELINE VORTEX 7000HHP...
  • Page 27 SERIOUS DAMAGE to the unit. Always park the unit in a heated building when not in use. If a heated building is not available, drain all water from the mobile cleaning unit. BLUELINE VORTEX 7000HHP...
  • Page 28 High Pressure Solution Hoses 7. GENERAL SERVICE ADJUSTMENTS Vacuum Relief Valve Vacuum Pump Drive Belts Water Pump Drive Belt Float Valve Chemical Pump Packing Nut Adjustment, Chemical Metering & Selector Valves 32 Pressure Regulator Adding/Draining Engine Coolant 24 BLUELINE VORTEX 7000HHP...
  • Page 29 SECTION 3 8. TROUBLESHOOTING PTO (Power Take Off) Chemical System Vacuum/Blower Water Pump Automatic Pump-Out Digital Temperature Control Exhaust Diverter Valve BLUELINE VORTEX 7000HHP...
  • Page 30: Maintenance Chart

    ****Inspect after first week of operation, and remove any debris present. Inspect again after 2 to 4 weeks. *****Check pulley and hub set screws after first 50 hours of operation, and again at 100 hours of operation. ******Or every 6 Months. Whichever comes first. *******Or Yearly. Whichever comes first. 26 BLUELINE VORTEX 7000HHP...
  • Page 31 SECTION 3 BLUELINE VORTEX 7000HHP...
  • Page 32: Maintenance

    ENGINE NOTE: PNUELUBE (Part # 13-017) is the only oil that BLUELINE puts in the vacuum pump at Refer to the owner’s manual for specific the factory. Adding petroleum oil to synthetic oil is instructions.
  • Page 33 When removing the vacuum inlet filters, grip the plastic hexagon section of the filters. Grasping filters by the screen will damage or destroy the filters. WATER PUMP Refer to the provided Water Pump Operation Manual for specific instructions. BLUELINE VORTEX 7000HHP...
  • Page 34 Regularly proper torque is achieved. inspect the heat exchanger and if carbon build up is noted, manually clean the exhaust tubes with a wire brush. Proper maintenance of the truck engine 30 BLUELINE VORTEX 7000HHP...
  • Page 35 (regular tune-ups and use of proper fuels) will help VACUUM HOSES prevent excessive carbon build up. To ensure maximum hose life, BLUELINE If excessive carbon build up is occurring, inspect recommends that you wash out the hoses with and clean exhaust diverter valve to ensure proper fresh water daily.
  • Page 36: General Service Adjustments

    To tighten the water pump belt: 1. Loosen the bolts, which hold the water pump and oil pump to the frame base. 2. Adjust the position of the belt tensioning adjusting bolt until the proper belt tension is 32 BLUELINE VORTEX 7000HHP...
  • Page 37 CHEMICAL PUMP the packing nut. DO NOT over-tighten. Keeping the packing properly adjusted will eliminate possible leaks and will add to the overall life of the The VORTEX 7000HHP mobile cleaning unit ® valves. features a stainless steel chemical pump and metering system.
  • Page 38 2. To adjust the pressure regulator, turn the adjusting knob (while observing the pressure gauge ADDING/DRAINING ENGINE on the control panel) until you reach the desired COOLANT pressure. Refer to vehicle owners’ manual for recommended engine coolant types and temperature ranges. 34 BLUELINE VORTEX 7000HHP...
  • Page 39: Troubleshooting

    CHEMICAL, VACCUM, HEAT TRANSFER, SAFETY and WIRING systems featured in this unit. If there are malfunctions occurring on this unit which you do not understand, refer back to the OPERATION section of this manual and review SYSTEM BLUELINE VORTEX 7000HHP...
  • Page 40 Yes / No Yes / No Is voltage present? Replace float switch. Replace PTO solenoid. Repair or replace wiring as required. Yes / No Repair or replace wiring Replace switch. from PTO switch to PTO solenoid as required. 36 BLUELINE VORTEX 7000HHP...
  • Page 41 Yes / No See Water Pump or Start from the beginning. System OK. Yes / No Replace chemical selector valve. Replace chemical metering valve. Diaphragm in the chemical pump is ruptured. Replace or rebuild chemical pump. BLUELINE VORTEX 7000HHP...
  • Page 42 Are the three (3) blower filters located in the waste tank Clean strainer basket. Yes / No clean and in good condition? Clean or replace Check for blockage or obstructions Yes / No between machine and waste tank. filters. 38 BLUELINE VORTEX 7000HHP...
  • Page 43 Repair or replace wiring Is voltage present? as required from power switch to float switch. Yes / No Replace switch. Yes / No Repair or replace Replace check water pump. valves. Repair or replace wiring as required to switch. BLUELINE VORTEX 7000HHP...
  • Page 44 Yes / No Yes / No Determine and repair Pump is O.K.. Pump is O.K.. Replace the diaphragms(s), cause of blown fuse. head and manifold Replace fuse (30 amp). 40 BLUELINE VORTEX 7000HHP...
  • Page 45 Yes / No Yes / No Check sensor with plug Set controller to Set controller to Replace Replace disconnected for continuity. desired temperature. desired temperature. controller. controller. Is sensor ok? Yes / No Replace Replace controller. sensor. BLUELINE VORTEX 7000HHP...
  • Page 46 Does lever move freely? Yes / No Yes / No Replace diverter Repair or replace solenoid. as required. Remove cover on diverter valve to Replace Vacuum determine cause of lever not moving. Actuator. Repair or replace as required. 42 BLUELINE VORTEX 7000HHP...
  • Page 47: Illustrated Parts Listings

    SECTION 4: PARTS & ACCESSORIES 9. ILLUSTRATED PARTS LISTINGS Unit/Chemical Control Panel Water System Vacuum System Chemical System PTO Drive Diverter Valve/Exhaust Decals Electrical Diagrams Optional Equipment 10. ACCESSORIES Accessories BLUELINE VORTEX 7000HHP...
  • Page 48 GAUGE, HOUR METER VORTEX 26-017 GAUGE, TEMP VORTEX 30-031 LIGHT, PTO VORTEX 23-001 VLV, BALL 1/4FP BS 11-054 NUT, 2" CONDUIT METAL LOCK 30-032 CONDUIT ADAPTOR, 2" PVC MALE 61-344 ASSY,CONTROL PNL MOUNT VORTEX 59-890 MOUNT. PANEL VORTEX 44 BLUELINE VORTEX 7000HHP...
  • Page 49 CONNECTOR,1/8NPT X 1/4T HEX SS 21-007 FTTG,BRB 1/8 PX 5/16 H BR 21-026 NIP, 1/4 HEX BR 21-038 ELL, STREET 1/8 IN. BRASS 21-066 ELL, 1/8 P X 1/4 T SS *Not Shown *29-042 SWITCH, PTO TOGGLE *47-049 HARNESS, SPEED CONTROL BLUELINE VORTEX 7000HHP...
  • Page 50 ROD, THROTTLE CONTROL VORTEX 15-023 PIN, SPRING, 5/64 X 3/8 SS 10-102 STUD, 1/4-20 X 5/8 PRESS IN 66-148 KNOB, CONTROL 3-16 BORE 11-047 NUT, 8-32 SS NYLOK 11-050 NUT, 1/4-20 SS FLANGE LOCK 29-040 SWITCH,SHORT HINGE ROLLER 46 BLUELINE VORTEX 7000HHP...
  • Page 51 HEAT EXCHANGER, RADIATOR FLUID 69-104 ASSY, WATER PUMP VORTEX 69-125 VORTEX Y-STRAINER 69-126 VORTEX PRESSURE REGULATOR 69-131 HEAT EXCHANGER, UPPER XENTHERM 69-137 VACUUM EXHAUST HEAT EXCHANGER 69-129 ASSY, LOWER XENTHERM 69-130 RADIATOR THERMOSTAT ADAPTOR 61-275 ASSY,RADIATOR BYPASS VORTEX BLUELINE VORTEX 7000HHP...
  • Page 52 HOSE, 1/2" X 32" X 1/2" FTBS 21-064 ELL, 1/4 P X 1/4 T BRASS 18-016 HOSE, 3/16 X 16-1/2 1/4FT X 1/4FT 21-096 PLUG, 1/4 IN T BRASS 59-704 BRKT,WTR PUMP MNT VORTEX 37-024 BELT, AX55 48 BLUELINE VORTEX 7000HHP...
  • Page 53 GASKET, 1/16 NEOPRENE X 5"OD 61-283 ASSY,COVER FLOAT FRESH WAT VRTX 21-252 ELL, 1" FNPT SS 21-259 BUSHING, 1M X 1/2F REDUCER 21-174 NIPPLE, 1/2"PIPE X 4" SS 21-035 CONN, 3/8 M X 1/2 FP 25-005 DSC, 3/8X3/8FP BR BLUELINE VORTEX 7000HHP...
  • Page 54 23-021 REG, PRESS CAT #7670 VITON 21-088 BUSHING, 3/8 X 1/4 BRASS 34-020 SENSOR,WTR PRESS 0-3000 PSI VRTX 21-293 ELL, 3/8 P X 1/4 T SS 21-282 ELL, 3/8 P X 1/2 T 45 DEG SS 50 BLUELINE VORTEX 7000HHP...
  • Page 55 ASSY,ENG EXHST DEFLECTOR VORTEX 43-006 INSULATION, HEAT EXCH E-3 VRTX 21-074 ELL, 3/4 P X 1/2 T BRASS 21-065 PLUG, 1/2 SOLID BRASS HEX HD 58-246 BRKT, LWR XENTHERM MOUNT 18-118 HOSE,1/2 BRAIDED SS X 74" VRTX BLUELINE VORTEX 7000HHP...
  • Page 56 ELL, 3/4 P X 1/2 T BRASS 34-024 THERMOCOUPLER VORTEX 34-019 SENSOR, WTR TEMP 140-300F VRTX 18-139 HOSE,3/4 BRAIDED SS X 43" VRTX 21-247 NIPPLE,3/4 MPT X 3/4 JIC 18-118 HOSE,1/2 BRAIDED SS X 74" VRTX 58-259 PNL,HEAT SHIELD UPPER XENTHERM 52 BLUELINE VORTEX 7000HHP...
  • Page 57 FTTG, BRB 3/4 PX 3/4 H BR 14-006 CLAMP, HOSE #20 18-140 HOSE, 3/4" HEATER HOSE, 115" W/COVER 18-146 HOSE, 1/2 T X 1/2 T X 12 16-063 HOSE, 3/4" HEATER HOSE 18-142 HOSE, 1/2 T X 1/2 T X 88 BLUELINE VORTEX 7000HHP...
  • Page 58 COIL, SS Z RES 18-142 HOSE, 1/2 T X 1/2 T X 88 18-143 HOSE, 1/2 T X 1/2 T X 27 21-280 ELL, 1/2 P X 1/2 T SS 41-033 GROMMET, 1 ID X 1 3-4OD 54 BLUELINE VORTEX 7000HHP...
  • Page 59 ASSY, LVL SENSOR SHTOFF WASTE PMP 14-034 CLAMP, HOSE TWIN RING 5.5 TO 5.7 69-000 WIRING , LEVEL SENSOR SHUTOFF 16-061 HOSE,5"ID 6-1/4 W/REINFORCED 16-061 HOSE,5"ID X 6-1/4 W/REINFORCED 16-009 HOSE, INT VAC 2 IN. *48-023 VORTEX WASTE TANK LID SEAL KIT BLUELINE VORTEX 7000HHP...
  • Page 60 69-100 ASSY, VAC RELIEF VALVE VORTEX Item No. Part Number Description 66-132 BODY, VACUUM RELIEF VORTEX 61-262 ASSY,VACUUM RELIEF DISK 15-016 SPRING,VAC RELIEF VORTEX 66-133 WASHER, RELIEF VALVE VORTEX 11-019 NUT,3/8-16 NYLOK 14-032 PIN, COTTER 7/64 X 3/4 SS 56 BLUELINE VORTEX 7000HHP...
  • Page 61 VLV, BALL 1-1/2 FP PVC DUMP 61-002 BASKET, STRAINER WASTE TANK 14-010 CLAMP, HOSE #32 14-024 CLAMP, HOSE #48 19-013 CAP, WASTE TNK INLET VORTEX *REDUCER, 2-1/2" TUBE - 2" HOSE #19-014 **1 IN SPONGE GASKET #41-018 BLUELINE VORTEX 7000HHP...
  • Page 62 Blower Mount Upper Frame 16-061 HOSE,5"ID X 12-1/2FT W/REINFORCED 63-072 MUFFLER, VAC EXHAUST VORTEX 16-061 HOSE,5"ID X 12-1/2FT W/REINFORCED 61-324 Blower Mount Lower Frame 61-340 ASSY, BLOWER EXH HE ADAPTOR 69-137 Vacuum Heat Exchanger 14-026 CLAMP,HOSE #80 58 BLUELINE VORTEX 7000HHP...
  • Page 63 29-037 SWITCH, PUSH BUTTON SELECTA 29-038 SWITCH, BOOT PUSH BUTTON 23-049 VLV,2" SMITH-COOPER BRASS BALL 21-220 NIPPLE, 2 IN SCHD 40 CLOSED 21-222 ELL, 2" 45 DEG STREET ABS 21-225 BARB, 2" MPT X 2" HOSE ZINC BLUELINE VORTEX 7000HHP...
  • Page 64 ASSY, 8IN STAINLESS HOSE REEL 51-013 MOLDING LARGE MOUTH JUG 21-025 CAP, 5 IN. WATER BOX/TANK BLACK 59-084 PNL, 5 GAL JUG HOLDER SS 20-002 STRAINER, SUCTION END 1/8FP 21-007 FTTG,BRB 1/8 PX 5/16 H BR 60 BLUELINE VORTEX 7000HHP...
  • Page 65 ELL, STREET 1/8 IN. BRASS 21-007 FTTG,BRB 1/8 PX 5/16 H BR 21-066 ELL, 1/8 P X 1/4 T SS 14-007 CLAMP, HOSE # 4 16-017 45" HOSE, BRAIDED 5/16 IN. 300FT BULK 18-077 HOSE, 3/16 X 38 1/4F X 1/4F BLUELINE VORTEX 7000HHP...
  • Page 66 BEARING, PILLOW 1-1/2 IN 66-137 SHAFT, BLOWER DRIVE VORTEX 39-023 BEARING, PILLOW 1-7/16 IN 39-025 SHAFT, DRIVE LINE VORTEX 45-015 PTO, AISIN TRANSMISSION A45043L 61-338 ASSY, PTO SHAFT GUARD VORTEX 58-216 BRKT,SOLENOID HYDRAULIC VRTX 23-060 VLV, SOLENOID PTO VORTEX 62 BLUELINE VORTEX 7000HHP...
  • Page 67 HUB, SDS 1-3/4 37-054 BELT, 5VX 900 38-045 PULLEY, 2B50 SDS 37-024 BELT, AX55 21-076 BUSHING, 1/4 M X 1/8 F BRASS 21-028 CONN, 1/8 P X 1/4 POLY 69-135 VORTEX BLOWER GUARD ASSEMBLY 35-009 FAN, 4 INCH CABINET BLUELINE VORTEX 7000HHP...
  • Page 68 ASSY,BELT TENSIONER BRACKET 15-021 SNAP RING, 5/8" SHAFT RETAINER 66-151 SHAFT, BELT TENSIONER VORTEX 66-153 PULLEY, TENSIONER VORTEX 15-022 SNAP RING, 1-7/8" INTERNAL 39-024 BEARING, 20MM X 47MM X .8125 66-150 LOCK RING, BELT TENSIONER VRTX 64 BLUELINE VORTEX 7000HHP...
  • Page 69 ASSY, EXHAUST ELBOW VORTEX 18-123 HOSE,3/16 X 23 X 1/4T NO COVER 14-011 CLAMP, HOSE FUEL #6 21-007 FTTG,BRB 1/8 PX 5/16 H BR 21-240 TEE, 1/8 NPTF BRASS 21-001 CONN, 1/8 P X 1/4 T BR BLUELINE VORTEX 7000HHP...
  • Page 70 WASHER, 5/16 NORD LOCK 11-036 NUT, M8 X 1.25 HEX JAM 12-033 WASHER, LOCK M8 SS 10-078 SCREW, 10-32 X 1/2 SHCS ZINC 12-026 LKWSR, #10 INT EXT 18-123 HOSE,3/16 X 20 X 1/4T NO COVER 66 BLUELINE VORTEX 7000HHP...
  • Page 71 Item No. Part Number Description 11-001 NUT, 1/4-20 SS 66-158 COVER,DIVERTER HOUSING VORTEX 66-159 BUSHING,CVR DIVERTER VORTEX 10-007 SCREW, MACH 1/4-20 X 1/2 SOCHD SS 61-278 ASSY,DIVERTER VALVE VORTEX 66-160 BUSHING, DIVERTER BODY VORTEX 61-279 ASSY,DIVERTER BODY VORTEX BLUELINE VORTEX 7000HHP...
  • Page 72 BRKT, EXHAUST SOLENOID 23-048 VLV, SOLENOID EXHAUST VORTEX 20-024 BREATHER STONE,1/8 NPT SS VRTX 21-001 CONN, 1/8 P X 1/4 T BR 18-122 HOSE,3/16 X 65 X 1/4T NO COVER 18-123 HOSE,3/16 X 23 X 1/4T NO COVER 68 BLUELINE VORTEX 7000HHP...
  • Page 73 SECTION 4 BLUELINE VORTEX 7000HHP...
  • Page 74 SECTION 4 ELECTRICAL DIAGRAM 70 BLUELINE VORTEX 7000HHP...
  • Page 75 Water Tank Float Switch (NC) 21 BLU/PNK Water Pump Clutch Power Diverter Solenoid Power 23 WHT/GRN Tach Sensor 24 GRN/BLK Tach Sensor Computer Module (In Truck Cab) 26 BLU/RED Computer Module (In Truck Cab) 27 GRN/RED Computer Module (In Truck Cab) BLUELINE VORTEX 7000HHP...
  • Page 76 WAND, LOW PROFILE 2 IN 25-000 DSC, 1/4M X 1/4FP BR 27-013 VLV, WAND CMP 21-050 CONN, 1/4 P X 1/4 T BRASS 18-021 HOSE, 3/16 X 51 1/4FT X 1/4FT 24-000 TIP, SPRAY 95015X1/8P SST 72 BLUELINE VORTEX 7000HHP...
  • Page 77 WAND,ERGONOMIC W /SPRAYER 25-000 DSC, 1/4M X 1/4FP BR 23-035 VLV,SPRAYER HYPRO 3381-0032 21-050 CONN, 1/4 P X 1/4 T BRASS 18-021 HOSE, 3/16 X 51 1/4FT X 1/4FT 24-000 TIP, SPRAY 95015X1/8P SST 40-009 HANDLE, ERGO WAND COATED BLUELINE VORTEX 7000HHP...
  • Page 78 CLAMP, HOSE #20 16-004 72” HOSE, WTR. 3/4 IN HRZ. 500FT BULK 69-000 WIRING , LEVEL SENSOR SHUTOFF 16-018 24” HOSE, WTR. 1 IN HRZ. 100FT BULK 21-036 FTTG, BRB 1-1/4 P X 1 IN. BARB 74 BLUELINE VORTEX 7000HHP...
  • Page 79 SECTION 4 68-102 KIT, VORTEX STORAGE RACKS 68-013 ASSY, VAN STORAGE UNIT SS BLUELINE VORTEX 7000HHP...
  • Page 80 SECTION 4 68-014 ASSY, SINGLE 5 GAL JUG HOLDER 68-015 ASSY, FURN BLOCK HOLDER SS 76 BLUELINE VORTEX 7000HHP...
  • Page 81 SECTION 4 68-016 RACK, DOUBLE CHEMICAL 68-018 ASSY, 10 GAL CHEM RACK S.S. BLUELINE VORTEX 7000HHP...
  • Page 82 SECTION 4 68-019 SPRAY BOTTLE HOLDER SS 68-022 ASSY, DBL PMP UP SPRAY RK, SS 78 BLUELINE VORTEX 7000HHP...
  • Page 83 SECTION 4 68-024 ASSY, SNG PMP UP SPRAY RK, SS 68-023 ASSY, REEL HP SOLUTION BLUELINE VORTEX 7000HHP...
  • Page 84 SECTION 4 68-025 ASSY, HOSE REEL HIGH PROFILE 68-033 ASSY, HOSE REEL H. PROFILE W-MTR 80 BLUELINE VORTEX 7000HHP...
  • Page 85 SECTION 4 68-037 ASSY, HOSE REEL VAC ONLY 68-045 ASSY, WATER SOFTENER BLUELINE VORTEX 7000HHP...
  • Page 86 SECTION 4 68-109 ASSY, KIT WATER SOFTENER VRTX 82 BLUELINE VORTEX 7000HHP...

Table of Contents