Your safety is of the utmost importance to us. This product manual contains information that is vital to the safe operation and maintenance of the VK Link. This manual also contains the performance data required to design appropriate, efficient airflow systems.
• Remove the remote control batteries if not in use for an extended period. • The VK Link may only be installed by a qualified HVAC designer or specialist. The VK Link is not intended to be installed by end users.
VK Link - 1_en 2.2. Regulatory Information Use environment: The Radic8 VK Link is intended for indoor use only. The unit must not be installed outdoors or anywhere that it will be exposed to water, rain, or the elements. Principle method: Air is purified through mechanical filtration and active decontamination utilizing PCO (photocatalytic oxidation) technology.
Page 7
Radic8 VK Link - 1_en Transport and Storage Symbols Acceptable upper and lower limits of atmospheric pressure for transport and storage. Acceptable upper and lower limits of relative humidity for transport and storage. To indicate correct upright position of the transport package.
Radic8 VK Link - 1_en 3. Warranty The warranty period for this unit is the standard manufacturer’s warranty of 12 months. This warranty may be extended by prior agreement with authorized distribution partners. Please refer to your local distributor for queries related to warranty or claims.
4. Product Overview The VK Link is a versatile clean air component for use in any number of ventilation or air delivery applications. It can form the heart of a modern ventilation design or be integrated into existing ducting or HVAC configurations.
It is important that the VK Link only be installed into a design created by a relevant specialist or retrofitted into an existing system by a qualified professional, taking into account all application variables, airflow dynamics, access, and safety considerations.
5.2. Wiring Before installation or use, ensure the correct mains AC voltage. The VK Link, control panel, and 200mm inline fan are connected as follows: Connect the 200mm inline fan to the control panel via the mated 4-pin communication and power cable.
) will illuminate. Switching the Reactor Chamber on or off The VK Link’s Reactor Chamber can be switched on or off independently by pressing the UV-C button ( When the Reactor Chamber is on, the UV-C indicator ( ) is illuminated.
Page 22
Radic8 VK Link - 1_en Adjusting fan speed The speed of the inline fan can be adjusted by pressing the fan button ( ). This will cycle between four fan speed settings: AUTO Automatic fan speed FAN 1 Low fan speed...
Page 23
Radic8 VK Link - 1_en Setting the time On the control panel: 1. Press and hold the mode button ( ) for 3 seconds to enter time adjustment mode. 2. The time will appear on the display panel and the last digit will flash.
Maintenance should only be performed by a qualified HVAC specialist, installer, or facility maintenance contractor. Maintenance of the VK Link and replacement of consumables is essential to ensure the longevity of the device. Ensure the unit is switched off before conducting any maintenance.
Radic8 VK Link - 1_en 7.1. Cleaning the Pre-Filter The pre-filter should be cleaned regularly to remove buildup of trapped material and ensure optimal airflow. 1. Slide out the pre-filter. 2. Clean the pre-filter by wiping it with a dust or microfiber cloth.
Radic8 VK Link - 1_en 7.2. Replacing the Carbon and HEPA Filters The carbon and HEPA filters are not reusable and should be replaced every 6 months. Carbon filter 1. Slide out the used carbon filter. 2. Safely dispose of the used carbon filter (see below).
Page 27
Radic8 VK Link - 1_en HEPA filter 1. Slide out the used HEPA filter. 2. Safely dispose of the used HEPA filter (see below). 3. Slide in a new HEPA filter. Safe disposal of filters • After used filters have been removed, we recommend lightly misting the used filter material with an alcohol-based sanitizer.
Page 30
9. Reconnect the Reactor Chamber power connector ( 10. When safe to do so, switch on the VK Link and hold the fan button on the control panel for 10 seconds to reset the Reactor Chamber runtime to zero. This will also turn off the control panel UV-C replacement indicator.
Radic8 VK Link - 1_en 7.4. Troubleshooting Control panel display errors: The temperature of the internal PCB has exceeded 80°C. Switch the unit off. The fan motor is not functioning correctly. Switch the unit off. Please contact your local distributor if any of the above errors are displayed.
Radic8 VK Link - 1_en 8. Specifications Radic8 reserves the right to make changes to the design and specifications of the VK Link without prior notice. Firmware version 1.1 Model VK Link Coverage* Net weight 14.1kg (31lbs) Dimensions (mm) 365 × 330 × 528 Dimensions (in) 14.37 ×...
Radic8 VK Link - 1_en 8.1. Performance Data VK Link efficiency Filter efficiency 99.995% Airflow 220–270 CFM Filter face area 0.084 m Static pressure drop (max fan speed) 230Pa 200mm inline fan performance Model VTRONIC W200-1 Weight 4.1kg (9lbs) Dimensions (mm) 350 ×...
Radic8 VK Link - 1_en 9. Support For VK Link hardware support, please contact your local VK Link distributor. Radic8 PTE Ltd 7 Temasek Boulevard #12-07 Suntec Tower One Singapore 038987 info@radic8.com You can find the model and serial number on the back of your device.