Gocom GD800 User Manual
  1. Manuals
  2. Brands
  3. Gocom Manuals
  4. Radio
  5. GD800
  6. User manual

Gocom GD800 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Digital Radio
User's Manual
335100413_RevA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GD800 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gocom GD800

Summary of Contents for Gocom GD800

  • Page 1 Digital Radio User's Manual 335100413_RevA...
  • Page 3 To Users Thank you for purchasing out product! This Manual (contains both analog and digital radios) is designed to make you quickly grasp the use of the device. In order to avoid physical injury or property loss due to improper operation, please read this Manual carefully before using the device.

  • Page 4: Safety Information

    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and . 2. this device must accept any interference received, including interference that may cause undesired operation. ISEDC RSS warning This product meets the applicable Industry Canada technical specifications.
  • Page 5 may cause minor burns when it comes into contact with the skin. ·Do not expose the radio to direct sunlight for a long time or place it near the heating Radio. ·If you wear a portable radio, make sure the antenna is at least 2.5 cm away from your body when the radio is transmitting.
  • Page 6 To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50 % of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance).

  • Page 7: Rf Radiation Information

    European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive ： The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries.
  • Page 8 • Les instructions de sensibilisation des utilisateurs doivent accompagner l'appareil lors de leur transfert à d'autres utilisateurs. • N'utilisez pas cet appareil si les exigences opérationnelles décrites ici ne sont pas remplies. Mode d'emploi: • Ne transmet pas plus que le facteur de marche nominal de 50% du temps.
  • Page 9 INFORMATION CONCERNING SAR FOR CE Max. SAR Level(s) Measured Limit (W/Kg) 0.164 W/kg 10g Head SAR 0.181 W/kg 10g Body SAR INFORMATION CONCERNING SAR FOR FCC Max. SAR Level(s) Reported Limit (W/Kg) 0.85 W/kg 1g Head SAR 1.26 W/kg 1g Body SAR...

  • Page 10: Product Control

    Product Control Antenna Power key LED Indicator Up key PTT key Headset Port Down key USB Port Menu key Programmable key Display Microphone Speaker Charging contacts...

  • Page 11: Display Guide

    Display Guide Channel display Signal strength Battery Level icon Volume icon VOX icon DCS Code icon CTCSS Code icon Channel indication Digital mode Analog mode Scan icon Radio LED Indicators LED Indication Radio Status Standby Green Slow Flash Low Battery Red Fast Flash Transmit (TX) Solid Red...

  • Page 12: Battery Installation

    Battery Installation 1. Use finger tip to pull the latch as shown in picture below to remove battery cover. 2. Put the battery pack into the battery compartment, close the battery cover with snap fit all latches. Ensure the battery cover is fully fix to radio. 熟...

  • Page 13: Belt Clip Installation

    Belt Clip Installation 1. Align the guide groove of the belt clip to the belt clip holder on the battery cover and install it appropriately. Note: The belt clip can be installed from any direction, clip on the belt, and the radio can rotate 180 degrees.

  • Page 14: Charging Function

    Charging Function 1. This device can support charging with charger tray or direct USB charging . During charging, the battery icon flashing on the display; when complete charging, the icon stops scrolling and shows battery full. 熟 悉 本 USB charging Device charging 机...

  • Page 15: Power On/Off

    ·During charging, it is not recommended to transmit the radio. ·The battery pack may slightly heat up during charging, which is a normal phenomenon. Power On/Off To turn on radio, press and hold [Power] key 3 seconds. To turn off radio, press and hold the [Power] key to turn off the radio and prompt tone will be sounded.

  • Page 16: Menu Selection

    and keep the microphone 2.5-5 cm away from the mouth. When transmitting, the radio should be at least 2.5 cm away from the head or body. ·Do not turn on/off the radio repeatedly during use, and adjust the volume to a level suitable for your hearing. ·Before using the radio for communication, please set the transmitter and receiver to the same frequency point.

  • Page 17: High/Low Power Setting

    the [+] or [-] key to start/stop channel scanning, and the speaker will give a voice prompt "Scan on" or "Scan off".During scanning, the digital radio scans the channels in the list and the current main channel. When any channel in the scan list is transmitting a signal, it will stay on that channel after scanning the signal.

  • Page 18: Power Saving Function

    Voice Control Function (preset by [Program] key) 1. Preset the [Program] key to [VOX On/Off] key through programming software. 2. Press the preset [VOX On/Off] key to turn on/off the voice control function. VOX levels can be preset through programming software: Level 1, Level 2, and Level 3, where Level 3 is the most sensitive.
  • Page 19 Program Key 1. Configure the functions of [Program] key through programming software. 2. The [Program] key of analog Mode includes the following functions: VOX On/Off, Monitoring Mode, Sub-audio Frequency On/Off. 3. The [Program] key of digital Mode includes the following functions: High/Low Power Switch, VOX On/Off, Monitoring Mode, One Touch Call, Emergency Alarm, etc.
  • Page 20 Squelch Step (SQ) 1. SQ is only valid for analog channels. 2. After SQ is set to 0, the speaker will automatically turn on and be in the monitoring state. 3. The higher the SQ step, the better the noise floor suppression effect. 4.

  • Page 21: Dtmf Function

    or re-burn it. DTMF Function 1. The DTMF interface of the programming software can configure the DTMF function, such as side tone, duration, interval time, online telegram code, offline telegram code, transmission start sound, transmission end sound, transmission start and end sound. 2.

  • Page 22: Color Code

    3. The same encryption template must be configured for transmitter and receiver for normal intercom, otherwise the speech content cannot be heard clearly. 4. The main purpose is to prevent the content of the speech from being monitored by other people at the same frequency. Color Code 1.

  • Page 23: Backlight Time

    3. The transmitter's red indicator stays on for a few seconds, and then press the [PTT] key to transmit. 4. The receiver's green indicator stays on for a few seconds, and then it can receive normally. Remote Monitor(private call only) 1.

  • Page 24: Language Settings

    4. Backlight time can be written directly by programming software. Language Settings 1. Language supports: Chinese and English. 2. Language can be set by programming software. 3. After switching the language, all voice broadcast will be changed to the language. 4.

Table of Contents