Download Print this page

Santa & Cole Rama Installation Manual

Area light anchor kit and pole

Advertisement

Quick Links

Rama
Area Light Anchor Kit and Pole
Installation Guide
Included components
1x – wooden drill template
Included: hardware is galvanized
4.5m and 6m pole: (4) anchor bolts, 3/4"-10 x 17" x 3" hook ,
(8) heavy hex nuts, 3/4" x 10, (8) flat washers, .81 ID" x 1.5" OD x 0.13" thick
8m (5in/6in) pole: (4) anchor bolts, 3/4"-10 x 17" x 3" hook ,
(8) heavy hex nuts, 3/4" x 10, (8) flat washers, .81 ID" x 2" OD x 0.13" thick
8m and 9m (5in/7in) pole: (4) anchor bolts, 1"-8 x 36" x 4" hook,
(8) heavy hex nuts, 1" x 8, (8) flat washers, 1.06" ID x 2.00" OD x 0.15" thick
Tools Required
• Safety glasses
• Wrenches, 1-1/4" for 4.5m, 6m or 8m (5in/6in) pole
• Wrenches, 1-5/8" for 8m or 9m (5in/7in) pole
• Level
LIGHTING LAYOUT RECOMMENDATIONS:
Refer to the product data sheet available at
recommendations for light pole spacing.
Landscape Forms is not responsible for site preparation and footings. The following
chart gives necessary information for calculating proper footing size, depending on the
specified light pole.
WARNING! Pole mounted luminaires must be attached either before or immediately
after pole installation. Failure to do so may cause vibration damage to the pole and will
void the pole warranty.
Pole Size
Base Overturning Moment (ft-lbf) Base Shear (lbf)
5" x .125" x 4.5m
5" x .188" x 6m
6"/5" x .188" x 8m
7"/5" x .188" x 8m
11,826
7"/5" x .188"x 9m
10,636
*Calculations per AASHTO 1994, assuming base of the pole is at
grade level, with 90mph fastest mile wind speed with 1.3 gust max.
8m
4.5m, 6m
Pole height
Pole height
5in/6in dia
8m, 9m Pole Height
5in/7in dia
www.landscapeforms.com
for
4037
353
5874
400
8633
455
566
494
INSTALLATION PROCEDURE FOR ANCHOR BOLTS:
1.
Prepare footing as required by local codes.
2.
Install anchor hooks, hex nuts, washers and wooden template as shown in Fig 3 and
Fig. 4. Level template in all directions. Note: template thickness is less than base
plate thickness. Dimensions given account for the difference.
3.
After footing has properly cured, remove wooden template. Do not remove lower
hex nuts or washers.
Fig. 1 – Sidewalk setback
Fig. 3 – Anchor install detail, 5in or 6in pole
5" diameter pole
6" diameter base pole
Date: September 30, 2021
www.landscapeforms.com
Ph: 800.521.2546
Fig. 2 – Base plate
orientation
to luminaire
Fig.4- Anchor install detail, 7inpole
7" diameter base pole
Page 1 of 2

Advertisement

loading

Summary of Contents for Santa & Cole Rama

  • Page 1 Rama Area Light Anchor Kit and Pole Date: September 30, 2021 Installation Guide www.landscapeforms.com Ph: 800.521.2546 Included components INSTALLATION PROCEDURE FOR ANCHOR BOLTS: Prepare footing as required by local codes. Install anchor hooks, hex nuts, washers and wooden template as shown in Fig 3 and Fig.
  • Page 2 Included components INSTALLATION PROCEDURE FOR LIGHT POLE: Lift the light pole into position over the installed anchors (refer to Rama anchor kit installation guide) as shown in Fig. 5. Ensure that the base plate is resting on all four washers.