Related Manuals for Ingenico AXIUM EX-SBASE-W
Summary of Contents for Ingenico AXIUM EX-SBASE-W
- Page 1 Model:AXIUM EX-SBASE-W WWW.ingenico.com 28-32,boulevard de Grenelle, 75015 Paris - France/ (T)+33(0)1 58 01 80 00 / (F)+33 (0)1 58 01 91 35 Ingenico-SA au capital de 47 656 332 / 317 218 758 RCS Nanterre...
-
Page 2: Table Of Contents
Contents 1. Product Introduction ............................3 1.1 Open Package Inspection ..........................3 1.2 Device Introduction ............................. 3 1.3 Interface definition ............................3 2. Product Technology Features ........................... 4 2.1 Product Technology Specifications ......................4 2.2 Environmental Conditions .......................... 4 2.3 Product Functions ............................5 2.4 Instructions .............................. -
Page 3: Product Introduction
1. Product Introduction 1.1 Open Package Inspection Open the package to check if there are any disabling masks or transportation damage in the terminals and fittings. Procedures： 1) Open the package 2) Check the following items(Subject to actual product configuration) ... -
Page 4: Product Technology Features
ETH_TX+ ETH_TX- ETH_RX+ ETH_RX- 2） USB-TYPE B interface Sequence USB-TYPE BSignal Not connect 2. Product Technology Features 2.1 Product Technology Specifications a USB type-C power port Port a RJ45 network port a USB B DEVICE port supporting USB2.0 Charge output: 5.0VDC 1.4A Power Power adapter: input 100-240V AC, 50/60Hz;... -
Page 5: Product Functions
2.3 Product Functions The base has three main functions as below: Place EX pos on the base to get charged. Place EX pos on the base. Connect the USB type-B to computer to extend the USB port. Serves as a router. -
Page 6: Wifi Connection
3. WiFi Connection 3.1 Connect EX pos to the base WiFi Power on the base. Check the SSID and password from the label on the back of base. Click “Settings” menu on EX pos,and then click “Network and Internet”, enter “ Wi-Fi” and select the base SSID to connect.(step 1~4). - Page 7 User can get and change the Ethernet parameter on the Network page. User can get and change the WLAN parameter on the WLAN page.
- Page 8 User canchange the operating mode,enable DMZ or set static DHCP on the Advanced page. User can update the firmware of base, save and reload the settings, change the password on the Manage page.
-
Page 9: Restore Factory Setting
3.3 Restore factory Setting Use sharp to click the RESET button for 3 seconds to restore the factory setting of the base. The position of RESET button is in chapter 1.2. 4. BASE Setting From EX pos 4.1 Get the Admin permission ... -
Page 10: Ethernet Parameter Setting
4.2 Ethernet Parameter Setting Procedures: Tab on “Network”enter WAN Setting or LAN Setting menu. Enter WAN Setting to get and set the WAN parameter. Enter LAN Setting to get and set the LAN parameter. Step 1Step 2 4.3 WLAN Parameter Setting ... -
Page 11: Advanced Setting
4.4 Advanced Setting Enter advanced menu. We can set the operating mode,DMZ and static DHCP of the base[Chart 1]. In operating mode,we can set the base work in different mode[Chart 2]. We can set DMZ[Chart 3]and add static DHCP[Chart 4]. [Chart 1] [Chart 2] [Chart 3]... -
Page 12: Bridge Mode
4.5.2 Bridge Mode Base distribute the IP to the computer and EX pos. They are in the same network segment . 4.5.3 WiFi Repeater Mode It is a mode to expand coverage of base. For example , Ex pos is too far away to connect Base A. So we can put Base B between Base A and EX pos. -
Page 13: Fixing Of The Power Cable
Check the version of the base[Step3]. [Step1][Step2][Step3] 5. Fixing of the power cable In some scenes,we want to fix thepower cable of the AXIUM EX-SBASE-W. Plug in the power cable and latch the metal hook on the cable,as follows:... -
Page 14: Faqs
50cm from the wall, heat source, cold source, window or air inlet. 9. Power Adapter The base can only be connected to the adapterwhich is provided with AXIUM EX-SBASE-W. WARNING The power adapter provided is specially designed for ingenicoAXIUMEX-SBASE-W. Do not use any other power supply. -
Page 15: Standard
10. Standard FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 16 brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement. RF exposure The antenna of the product,under normal use condition is at least 20cm away from the body of theuser.Warning statement to the user for keeping 20cm separation distance and the prohibition of operating to a person has been printed on the user manual.So,this product under normal use is l0cated on electromagnetic far field between the human body.
- Page 17 Care has been taken to ensure that the content of this document is as accurate as possible. ingenico however declines any responsibility for inaccurate, incomplete or outdated information. The contents...