Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for cyclotest mySense
Summary of Contents for cyclotest mySense
- Page 1 Instructions for use www.cyclotest.de...
-
Page 2: Table Of Contents
® Operating the device app via a Bluetooth 4.0 interface. Device description Display The device is intended exclusively for use with the cyclotest mySense ® Initial device setup app. The device cannot be operated without the cyclotest mySense ®... -
Page 3: Safety Instructions
Safety instructions Safety instructions • The device must be used solely for the purpose described in these operating instructions. The manufacturer shall not be held liable for any damages resulting from improper use. • Do not allow the thermometer to fall on the floor. The thermometer is not shock-resistant or impact-resistant. -
Page 4: Operating The Device
Illuminated display Initial device setup You must install the cyclotest mySense app on your smartphone be- ® fore setting up the device for the first time. The cyclotest mySense ® basal body temperature thermometer cannot be set up without the cyclotest mySense app. -
Page 5: Temperature Measuring
The date and time are synchronised automati- saved, the most-recently measured value is cally from the mySense app. To do this, the de- shown in the display with an M (memory). The vice connects to the app via Bluetooth (Figure 2). - Page 6 • If more than 25 saved measurements have • As long as the measured temperature re- not been transferred to the mySense App, the mains below the measuring range (32.00°C message “APP/FULL” (Figures 5 and 6) appears to 43.99°C), the display shows L (low) (Figure...
-
Page 7: Recalling Saved Measurement Values
1; the value measured prior to that is stored ues, as well as the date and time, to the mySense app after each meas- in save slot 2, and so on. If more than 30 measurements are taken, urement. -
Page 8: Battery Display/Changing The Battery
Figure 1 for the first time. Change the battery if: If your device is lost or faulty, you can assign a new mySense basal – After switching on the device, the “battery body temperature thermometer to your user account. flat” indicator (Figure 2) appears on the dis- play. -
Page 9: Technical Information Error Messages
Fever warning. Temperature higher than 37.5°C meas- ured. Technical data Device memory is full. Connect the thermometer to the cyclotest mySense ® Type: Maximum thermometer, direct mode app to transfer the measured values to the app. -
Page 10: Customer Service
Technical information Technical information Explanation of symbols Operating condi- Ambient temperature 10°C to 40°C, maximum tions: relative humidity 15% to 95% This product complies with Council Directive 93/42/EEC of 5 Conditions for stor- -25°C to +55°C, maximum relative humidity September 2007 concerning medical devices and bears the age and transport: 15% to 95% 0123... -
Page 11: Cleaning And Care
Cleaning and care Warranty • Clean the thermometer with a soft cloth and isopropyl alcohol dilut- The device has been manufactured and tested with all due care. Nev- ed with water or cold, soapy water. ertheless, in the event of defects upon delivery, we provide a warranty under the following conditions: •... -
Page 12: Cyclotest ® Service Hotline
® You have undoubtedly read our instructions on the use of cyclotest ® mySense carefully and have familiarised yourself with its character- istics. If you have any additional questions, you can call our cyclotest ser- ® vice hotline, which is available Monday to Thursday from 8:00am to 5:00pm and Fridays until 4:30pm. - Page 13 0640 PZN-14886326 cyclotest and UEBE are internationally protected trademarks of: UEBE Medical GmbH Zum Ottersberg 9 97877 Wertheim, Germany Phone: + 49 (0) 93 42 / 92 40 40 Fax: + 49 (0) 93 42 / 92 40 80 Email: info@uebe.com...
Need help?
Do you have a question about the mySense and is the answer not in the manual?
Questions and answers