Subscribe to Our Youtube Channel
Related Manuals for Marson MT80
Summary of Contents for Marson MT80
- Page 1 MT80 2D Mini Scan Engine, Integration Guide, V0.2 MT80 MT80 Mini Scan Engine) Mini Scan Engine) Integration Guide Integration Guide Version 0.2 DATE: 2018/01/10...
-
Page 2: Table Of Contents
MT80 2D Mini Scan Engine, Integration Guide, V0.2 TABLE OF CONTENTS INTRODUCTION.....................1 INTRODUCTION 1-1. MT80 Block Diagram................1 1-2. Electric Interface..................2 1-2. Electric Interface 1-2-1. Assignment................2 1-2-1. Assignment 1-2-2. Flex Cable..................5 1-2-2. Flex Cable SPECIFICATIONS....................6 SPECIFICATIONS 2-1. -
Page 3: Introduction
MT80 2D Mini Scan Engine, Integration Guide, V0.2 INTRODUCTION INTRODUCTION The MT80 2D Mini Scan Engine is designed for 1D Barcode and QR Code high performance barcode scanning with easy integration. MT80 is ideal for integration into data terminals and other small mobile devices. -
Page 4: Electric Interface
MT80 2D Mini Scan Engine, Integration Guide, V0.2 Electric Interface Electric Interface 1-2-1. Assignment 1-2-1. Assignment (Top View of MT80 Decoder Board) Pin1 Pin12 Pin# UART Description Schematic Example ------------ Supply voltage input. Must always be connected to 5V power supply. - Page 5 MT80 2D Mini Scan Engine, Integration Guide, V0.2 Pin# UART Description Schematic Example Power Off Power Off Input High: Scan Engine Off Low: Scan Engine On *Exception: 1. During data When Power Enable pin is pull high, scan engine transmission 2.
- Page 6 MT80 2D Mini Scan Engine, Integration Guide, V0.2 Pin# UART Description Schematic Example Output Active High, it indicates the status of Power-Up or a successful LED1 GREEN barcode decoded (Good Read). 330R Decode LED 2N3904 ------------ Input When Handshaking is...
-
Page 7: Flex Cable
1-2-2. Flex Cable The flex cable is used to connect MT80 to the host side. There are 12 pins on both the decoder board (MT80) side and the host side. Please see Chapter 2-6 for more details of flex cable. -
Page 8: Specifications
MT80 2D Mini Scan Engine, Integration Guide, V0.2 SPECIFICATIONS SPECIFICATIONS 2-1. Introduction 2-1. Introduction This chapter provides technical specifications of the MT80 scan engine. Operating method, scanning range and scan angle are also presented. 2-2. Technical Specifications 2-2. Technical Specifications Optic &... - Page 9 MT80 2D Mini Scan Engine, Integration Guide, V0.2 Decoder Board : 3.3g Color Black Material Imager : 25pin ZIF (pitch=0.3mm) Connector Decoder Board : 12pin ZIF (pitch=0.5mm) Imager to Decoder board : 25 pins flex cable (pitch=0.3mm) Cable Decoder board to Host: 12pins flex cable (pitch=0.5mm)
- Page 10 MT80 2D Mini Scan Engine, Integration Guide, V0.2 UPC-A/ UPC-E EAN-8/ EAN-13 Matrix 2 of 5 China Postal Code (Toshiba Code) Industrial 2 of 5 Interleaved 2 of 5 Standard 2 of 5 (IATA Code) Codabar Code 11 1D Symbologies...
-
Page 11: Interface
Characteristics: (1) Configurable by scanning configuration barcodes or ® Ez Utility (a PC-based software utility, available for download at www.marson.com.tw) (2) Supports hardware trigger only Interface Configuration Barcode: UART Scanning above barcode will set your MT80 to UART interface. ___________________________________________________________________________________... -
Page 12: Usb Interface
(1) Configurable by scanning configuration barcodes or Ez Utility ® (a PC-based software utility, available for download at www.marson.com.tw) (2) Supports hardware trigger only (3) Emulates a USB Keyboard device Interface Configuration Barcode: USB HID Scanning above barcode will set your MT80 to USB interface. ___________________________________________________________________________________... -
Page 13: Operation Method
MT80 enters Standby Mode and is ready for operation. 2. Once the MT80 triggered by either hardware or software method, it will emit a narrow, horizontal slab of light which is aligned with the sensor’s field of view. -
Page 14: Flex Cable Specification
MT80 2D Mini Scan Engine, Integration Guide, V0.2 Flex able Specification Flex able Specification Below is the drawing of 12 Pins flat cable(P/N: 67XX-1009X12) that comes with MT80. ___________________________________________________________________________________... -
Page 15: Connector Specification
MT80 2D Mini Scan Engine, Integration Guide, V0.2 Connector Specification Connector Specification Below is the drawing of 12 pins 0.5-pitch FPC Connector(P/N: 4109-0050X00) of MT80. ___________________________________________________________________________________... -
Page 16: Installation
1. ALWAYS use grounding wrist straps and a grounded work area when unpacking and handling the MT80. 2. Mount the MT80 in a housing that is designed for ESD protection and stray electric fields. 3-2. Mechanical Dimension 3-2. - Page 17 MT80 2D Mini Scan Engine, Integration Guide, V0.2 factors. Acrylic can be laser-cut into odd shapes and ultrasonically welded. Cell Cast ADC, Allyl Diglycol Carbonate (ASTM: ADC) Also known as CR-39 , ADC, a thermal setting plastic widely used for plastic eyeglasses, has excellent chemical and environmental resistance.
-
Page 18: Window Specifications
MT80 2D Mini Scan Engine, Integration Guide, V0.2 3-4. Window Specifications 3-4. Window Specifications MT80 Imager Side View Window Specifications for MT80 Integration Minimum Window Size Distance Tilt Angle (a) Horizontal (h) Vertical (v) Thickness (t) < 0.5 mm (b) -
Page 19: Window Care
3-5. Window Care In the aspect of window, the performance of MT80 will be reduced due to any kind of scratch. Thus, reducing the damage of window, there are few things have to be noticed. 1. Avoid touching the window as much as possible. -
Page 20: Development Kit
(P/N: 5300-1315X00) Micro USB Cable (P/N: 7005-9892A50) Due to the advantage of its small size, MB100 Multi I/O board is also suitable for being installed inside the host system, as an interface board connecting MT80 to the host device. ___________________________________________________________________________________... -
Page 21: Version History
MT80 2D Mini Scan Engine, Integration Guide, V0.2 VERSION HISTORY VERSION HISTORY Rev. Date Description Issued Checked 2017.11.24 Preliminary Draft Release Shaw Kenji & Hus 2018.01.10 Updated Chapter 5 Shaw Kenji Marson Technology Co., Ltd. 9F., 108-3, Mincyuan Rd., Sindian Dist., New Taipei City, Taiwan...
Need help?
Do you have a question about the MT80 and is the answer not in the manual?
Questions and answers