Subscribe to Our Youtube Channel
Summary of Contents for Lumberjack SG900
- Page 1 SAFETY AND OPERATING MANUAL Electric Paint Spray Gun SG900 ORIGINAL INSTRUCTIONS SG900...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Welcome to Lumberjack! Dear customer, Congratulations on your purchase. Before using the product for the first time please be sure to read these instructions for use. They provide you with all information necessary for using the product safely and to ensure its long service life. -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. SG900... - Page 4 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. SG900...
- Page 5 Always ensure sufficient circulation of fresh air. m) Never use paint containing lead. n)Before any work (such as transport, construction, conversion, cleaning or maintenance) and when the product is not being used, disconnect it from the power supply and empty the paint container! SG900...
- Page 6 Skin contact: Clean with plenty of water and soap, consult a doctor if necessary. Eye contact: Rinse with plenty of water, consult a doctor. Swallowing: Do not vomit, consult a doctor Inhalation: Fresh air, consult a doctor if necessary SG900...
-
Page 7: Symbols & Cable Rating Chart
Caution! Risk of Injury! Do Caution! Wear ear defenders. The not reach into the running impact of noise can cause damage saw blade to hearing. Protection class: Caution! Wear a dust mask. Double Insulated. SG900... -
Page 8: Machine Details And Product Features
27. Spray tip key 8.Spray width lever 16.5 Valve extension 9.Spray tip 17. Canister 10.Spray unit housing 18. Flow control knob 11.Trigger 19. Quick release lock 12.Quick refill lid 20. Switch trigger lever 13.sealing linear 21. Hanging hook SG900 AIR6V AIR6V AIR6V AIR6V... - Page 9 MACHINE DETAILS AND PRODUCT FEATURES SG900 AIR6V AIR6V AIR6V AIR6V...
-
Page 10: Assembly
(150 seconds lock (#19) and snap onto the hook on the edge or less). This is the “run out time”. Refer to the of canister lid. thinning table for information on the thinning required for different materials. SG900... -
Page 11: Operation
- Skin that forms on the top of paint can clog the sprayer. Remove skin before mixing. Strain with a funnel with a filter attached or through hosiery to remove any impurities that could clog system. - Before starting have gloves, paper towels, rags etc. available for unexpected spills. SG900... - Page 12 Release the trigger to turn off the tool. To select Horizontal Flat Jet, turn the air cap(#5) to vertical direction by turning the smart nozzle selector (#3) anti- clockwise until stop. SG900...
- Page 13 ADJUSTING WIDTH OF SPRAY PATTERN align with the skirt on spray unit housing(#10). By turning the Spray Width Lever (#8) between the Refer to Fig. for proper assembly. Minimum marking and Maximum marking, the width of the spray patterns can be adjusted accordingly. SG900...
- Page 14 - Always spray from a minimum of 50mm to a the flow knob clockwise increases the flow of maximum of 300mm. liquid. Turning the knob anti-clockwise decreases the flow of liquid. If runs or drips do occur, have a dry paint brush on hand to smooth them out. SG900...
-
Page 15: Cleaning
- Refill the canister with a small amount of new cleaning solution. Screw the canister back onto the sprayer. -Plug in the cord and turn on the power unit. - Spray the cleaning solution through the sprayer onto scrap material for 2 to 3 seconds. SG900... - Page 16 - Reassemble sprayer. Note: Spray nozzle can only be assembled in one direction that the notch of the nozzle(#6) must align with the skirt on spray unit housing(#10). SG900...
-
Page 17: Maintenance And Service
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. SG900... -
Page 18: Lumberjack Guarantee
If a return is requested by the Authorised Dealer or 1.2.3 If asked to do so by Lumberjack or its Lumberjack, you will be provided with a Returns Authorised dealer, you return the product at Material Authorisation number which must be your own cost to Lumberjack’s or supplying... - Page 19 Lumberjack. If you include a contact number with this it will speed your claim 2.4 Please note that it is essential that the letter of claim reaches Lumberjack on the last day of this Guarantee at the latest. Late claims will not be considered.
-
Page 20: Declaration Of Conformity
Old Heath Road, Wolverhampton, WV1 2RP. Tel: 01902 450 470 Declares that the Spray Gun( SG900 Is in compliance with the regulations included in the Directives:2006/42/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by Intertek Testing Services Hangzhou,16 No. 1 Ave.,Xiasha Economic Development District,Hangzhou,310018,China. -
Page 21: Parts List
Binding post Right shell components Screw Lead sealing ring Cord guard Hook rack Power cord Screw Cord bushing Suction canal Left shell components Motor Nozzle cleaner Capacitance Viscosity cup Motor damping ring Spanner Motor cabinet Brush SG900 AIR6V AIR6V AIR6V... -
Page 22: Parts Diagram
Parts Diagram SG900...
Need help?
Do you have a question about the SG900 and is the answer not in the manual?
Questions and answers