Philips 60PP960199 Quick Start Manual page 3

TV
T
ELEVISION BEGIN
1
button to turn the TV ON.
WABC
MENU
VOL CH
Remote Sensor
STATUS/EXIT
Window
R
EMOTE
B I BEGIN
ATTERY NSTALLATION
1
T
o load the supplied bat-
teries into the remote:
"System" button on the
remote
1. Remove the battery
sends its commands to the TV.
compartment lid on the
back of the remote. Point the remote control
toward the remote sensor win-
2. Place the batteries (2-
dow on the TV when operating
AA) in the remote. Be
the TV with the remote.
sure the (+) and (-) ends
of the batteries line up
correctly (inside of case is
marked.)
3. Reattach the battery lid.
A/V Button
Press to quickly select Auxiliary source
inputs on the TV (AUX1 VIDEO; AUX2
VIDEO; etc.), as well as Antenna A/B inputs,
and the last viewed channel on the TV.
Guide Plus+ Buttons
Press to use the Guide Plus+ electronic guide
for TV program listings and information.
Refer to your separate Guide Plus+ informa-
TV-VCR-ACC "S "
YSTEM
tion manual for setup and use details.
B
UTTONS
TV-ACC-VCR System Buttons
The remote's TV-ACC-VCR
Press to send remote signals to either the TV or
System buttons control how
accessory VCRs, Cable TV Converters, Laser
buttons on the remote are
Disc players, etc.
used.
Format Button
For example:
Press to display the TV in various height-to-
width screen display options or aspect ratio
With the "TV" system but-
controls (4x3 - Standard; Theater 1 & 2;
ton pressed:
Zoom 1 & 2, etc.).
the Menu ring buttons
and (+,-) buttons are used
Menu Select Buttons
to select and adjust on-
Press the Menu Select button to show on-
screen TV features.
screen controls. Press the outer Menu ring
button to move up and down (or left and
With the "VCR" system
right) through the list of on-screen controls.
button pressed:
Press the center Menu ring button to select
the Power, Channel, and
and access highlighted controls.
other dedicated VCR
Status/Exit Button
buttons (see remote's flip
down door) are used to Press to see the current channel number on
select and adjust VCR the TV screen. Also press to clear the TV
screen after control adjustments.
model features.
Volume Buttons
With the "ACC" system
Press to adjust the TV sound level up (+) or
button pressed:
down (-).
the Power, Channel
Number, and Channel
Mute Button
Up /Down buttons on
Press to turn the sound OFF on the TV. Press
the remote can work with
again to return the sound to its previous
Cable TV Converters,
level.
Laser Disc players, and
100+ Button
Home Satellite Dish
systems. Press to select channel numbers greater than
99 (by direct button entry). Press the 100 but-
ton then the remaining two digits to select
Note: For more details on
the desired channel.
how the TV remote works
with VCRs, Cable Converters,
VCR Buttons
and other accessory equip-
For use of VCR buttons see the "Using the
ment see the other owner's
Remote With a VCR" in your other owner's
manual supplied with your
manual.
TV.
All manuals and user guides at all-guides.com
R C
AND EMOTE
2
Press the VOLUME UP
Press the POWER
(+) or DOWN (-) buttons to
adjust the TV sound level.
2
SOURCE
SELECT
1
Press the TV
to be sure the remote
STOP
S H
MART ELP
can press any button on
the front of the TV to
turn the TV ON.
O
ONTROL PERATION
3
Press the CHANNEL UP
( ) or DOWN ( ) button to
select TV channels.
Note: Always press two number
buttons on the remote when
selecting channels.
For example: press "0" then "6"
for channel 6.
MENU
VOL CH
3
STATUS/EXIT
1
N
Press the Backlight button to illuminate or
light the remote's buttons to make them easier to
read and use in dark room conditions.
AV POWER
INFO
GUIDE
TV ACC
VCR
SWAP PIP CH SOURCE FREEZE
DN UP
FORMAT AUTO
STATUS/ MENU/
EXIT SELECT
VOL
CH
MUTE
1 2 3
4 5 6
7 8 9
0
100+
SURF
VCR
REC SLEEP
PLUS+
CLEAR
Open the remote control VCR button
area with the pull tabs located on both
sides of the hinged door.
Remember, You
The tuned channel number will
always briefly appear when the
TV is first turned ON (and with
channel changes.)
3
S
MART
H
ELP
Note: You
can press any of the
TV's front keyboard
buttons to turn the
TV ON, but the
Power button must
be used to turn the
set OFF (from the
STOP
TV's local key-
board).
3
Power Button
Press to turn the TV (or select VCR, Cable
Converters, etc.) ON and OFF.
PIP Buttons
Press to operate Picture-In-Picture features.
See "PIP" section in your other owner's
manual for details.
Auto Button
Press to select from a list of Auto controls.
Auto Picture for factory preset picture con-
trol levels (set for different types of viewing
sources and programs.) Auto Sound to
select various audio mode settings matched
to different types of TV programming. Auto
Surf to quickly select up to 10 channels
(separate from the TV's normal channel scan
memory). See the "Auto Features" section in
your other owner's manual for details.
Channel Scan Button
Press to scan up (+) or down (-) through
programmed channel numbers.
Number Buttons
Press the number buttons to select TV chan-
nels. Press two number buttons to select sin-
gle digit channels. For example: press "0"
then "6" for channel 6.
Surf Button
Press to select previously viewed channels.
With the TV's "Auto Surf" control ON you
can place up to 10 channels in memory.
Then by pressing the SURF button you can
quickly view the select channels.
See the "Auto Surf" section (in your other
owner's manual) to see how to select a series
of channels using the Surf button.
Sleep Button
Press to set the TV to automatically turn
itself Off. Press the Sleep button repeatedly
to select the amount of time (15 minutes to 2
hours) before the TV shuts Off.
You can also press the STATUS
button (on the remote) to see
what channel the TV is ON.