Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for RCBS Dillon Conversion Kit
- Page 1 Rifle Bullet Feeder — Dillon Conversion Kit ® PRODUCT INSTRUCTIONS...
- Page 2 WARNING! Before using the Rifle Bullet Feeder – Dillon Conversion Kit, read these instructions carefully to fully learn how to safely operate the related reloading equipment. Failure to properly operate the related reloading equipment can result in severe personal injury and/or equipment damage.
-
Page 3: Warning / Caution
Powder cans should be stored ammunition. Because RCBS has no control over the choice of components, the manner in which they are assembled, the use of this product, or the firearms in which the resulting ammunition may be used, we assume no responsibility, expressed or implied, for the use of ammunition reloaded with this product. - Page 4 UNPACKING Refer to the list below to identify parts as you unpack your new Rifle Bullet Feeder – Dillon Conversion Kit. Tube Bag #1 Bag #2 Coupling Parts Bag #1 Parts Bag #2 1/4-20 x 1/2” Long BHCS (4) Dillon PM Bracket 1/4-20 x 3”...
- Page 5 RCBS Rifle Bullet Feeder, not replace it. You will need to reference that document to complete your Bullet Feeder installation. Contact RCBS if you need another copy or see our website (www.rcbs.com) to download one. Photo 2. PM Bellcrank Locknut...
-
Page 6: Installation
INSTALLATION Note: Reference the part schematic on page 11 for more information. Bullet Feed/ Seat Die Installation First, tighten the setscrew on your PM Die Lock Ring to keep it from moving. Next carefully detach the PM Failsafe Rod from the Bellcrank Link Brackets (consult your Powder Measure Manual for more information). - Page 7 NOTE: You will be able to load cartridge lengths of Manually squeeze the Bullet Feeder’s Push Bar approximately 2.0 – 2.5 inches at this setting. For Mechanism, allowing the bullet to drop into the Seat longer cartridges, raise the Seat Die Assembly as Die Body (Photo 11).
- Page 8 Next, reinstall the PM Failsafe Rod to the Bellcrank Brackets (consult your Powder Measure Manual for more information). Place a properly sized/ trimmed case at the powder drop station and fully lower the Press Handle. The Cam on the PM Assembly should Triangular engage the Push Bar and drop a bullet into the Seat Die Bracket...
- Page 9 Refer to the Product Instructions received with your Strong RCBS Rifle Bullet Feeder for the remainder of the steps. Mounts CAUTION: A bullet will be fed with each cycling of the Push Bar. If a powder drop problem is incurred and...
- Page 10 ADJUSTMENT Note: Reference the part schematics on page 11 of this booklet and the Bullet Feeder Instruction Manual for more information during assembly and installation. Bullet Seating Depth Bullet seating depth is controlled by adjusting the Seat Plug Stop (A) up or down. Shorter length cases may be accommodated by moving the Retaining Ring to a higher groove on the free floating bullet Seat Plug (B) (Photo 20).
- Page 11 ITEM # PART # DESCRIPTION QTY. 781310 Dillon PM Bracket 781311 Dillon Adjustment Bracket 781312 Dillon Upper Tube 781313 Dillon Lower Tube 781314 Tube Coupling 781315 Dillon Clamp 781316 Dillon Clamp Anchor 181253 Cam...
- Page 12 RCBS 605 Oro Dam Blvd. East Oroville, CA 95965 Federal Premium Ammunition - RCBS - Alliant Powder - CCI - Speer Ammo - Speer Bullets Fusion Ammunition - Estate Cartridge - Blazer Ammunition - Force on Force...
Need help?
Do you have a question about the Dillon Conversion Kit and is the answer not in the manual?
Questions and answers