AEG ACS58B18 Instructions Manual

AEG ACS58B18 Instructions Manual

Hide thumbs Also See for ACS58B18:

Advertisement

ACS58B18
Original instructions

Advertisement

Table of Contents
loading

Summary of Contents for AEG ACS58B18

  • Page 1 ACS58B18 Original instructions...
  • Page 2 mportant! It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product. Subject to technical modifications.
  • Page 3 ACS58B18...
  • Page 4 CHAIN BAR MOUNTING COVER NUTS CHAIN SPIKED TENSIONING BUMPER SCREW SAW CHAIN GUIDE BAR COVER...
  • Page 5: Throttle Trigger

    FRONT HAND GUARD/CHAIN BRAKE FRONT HANDLE BATTERY TRIGGER RELEASE REAR HANDLE THROTTLE TRIGGER COMBINATION WRENCH CHAIN LUBRICANT GUIDE BAR...
  • Page 6: Adjusting The Chain Tension

    USING THE CHAING BRAKE ADJUSTING THE CHAIN TENSION CLEANING THE PRODUCT INSTALLING AND REMOVING THE GUIDE BAR COVER...
  • Page 7 INSTALLING AND REMOVING THE BATTERY START STOP USING THE PRODUCT ADDING CHAIN AND BAR OIL REPLACING THE CHAIN AND BAR STORING THE PRODUCT...
  • Page 8: Installing And Removing The Battery

    INSTALLING AND REMOVING THE BATTERY click...
  • Page 9 START USING THE PRODUCT STOP...
  • Page 10 BRAKE ON USING THE CHAIN BRAKE BRAKE OFF...
  • Page 11 ADJUSTING THE CHAIN TENSION...
  • Page 12 APPROX. 6.5 mm (0.256 in.) FLATS 7.85~9.8 Nm (80~100 Kgf-cm) click...
  • Page 13 ADDING CHAIN AND BAR OIL...
  • Page 14 click...
  • Page 15 REPLACING THE CHAIN AND BAR...
  • Page 16 NOTE: Always properly dispose of used chain and bar. NOTE: For replacment chain and bar part CHAIN DRIVE numbers, see page 25. LINKS GROOVE...
  • Page 17 APPROX. 6.5 mm (0.256 in.) FLATS...
  • Page 18 7.85~9.8 Nm (80~100 Kgf-cm) click...
  • Page 19 INSTALLING AND REMOVING THE GUIDE BAR COVER...
  • Page 20 CLEANING THE PRODUCT NOTE: Clean the the product with a with a soft-bristle brush or with a soft, dry cloth. NOTE: Do not clean the product with water.
  • Page 21: Storing The Product

    STORING THE PRODUCT...
  • Page 22 NOTE: Always remove excess chain and bar oil from the oil tank before storing the product. NOTE: Store the product in a cool, dry, and well- ventilated area that is inaccessible to children. Keep the product away from corrosive agents, such as garden chemicals and de-icing salts.
  • Page 23 Figure 1 Figure 6 Figure 2 Figure 7 Figure 3 Figure 8 5 cm / 2 in 5 cm / 2 in Figure 4 Figure 9 Figure 5 Figure 10...
  • Page 24 Figure 11 Figure 12 Figure 13 Figure 14 diffe An e Iden Figure 15...
  • Page 25: Intended Use

    ACS58B18 TECHNICAL DATA CORDLESS CHAINSAW Rated voltage 58 V Max bar length 450 mm Chain oil tank capacity 177 ml Weight (without battery pack, with guide bar, chain and empty tank) 5.08 kg Usable cutting length 385 mm Max no-load speed 21 m/s Vibration level (in accordance with EN 60745-1 &...
  • Page 26: Work Area Safety

    PERSONAL SAFETY have received adequate training on the hazards and preventative measures to be taken while using the product. It is not to be used Stay alert, watch what you are doing and use common sense by children or by persons not wearing adequate personal protective when operating a power tool.
  • Page 27: Chainsaw Safety Warnings

    BATTERY TOOL USE AND CARE Do not modify the product in any way or use parts and accessories that are not recommended by the manufacturer. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a WARNING! If the product is dropped, suffers heavy impact, ion.
  • Page 28 Keep handles dry, clean, and free from oil and grease. Greasy, oily Before starting the product, make sure that the saw chain is not handles are slippery causing loss of control. contacting any object. Cut wood only. Do not use chainsaw for purposes not intended. Do not modify the product in any way or use it to power any For example: do not use chainsaw for cutting plastic, masonry or attachments or devices not recommended by the manufacturer.
  • Page 29 INSTRUCTIONS CONCERNING PROPER Before felling starts, consider the natural lean of the tree, the location TECHNIQUES FOR BASIC FELLING, LIMBING, AND of larger branches, and the wind direction to judge which way the CROSS-CUTTING tree will fall. Remove dirt, stones, loose bark, nails, staples, and wire from the tree. Understanding the forces within the wood Do not attempt to fell trees that are rotten or have been damaged by When you understand the directional pressures and stresses inside...
  • Page 30: Operation

    Limbing a tree Adjusting the chain tension See figures 12 - 13. See pages 11 - 12. Limbing is removing the branches from a fallen tree. When limbing, 1. Remove the battery pack before you do any work on the chainsaw. leave larger lower limbs to support the log off the ground.
  • Page 31: Maintenance Schedule

    MAINTENANCE Always test the chain brake performance after cleaning. Refer to “Checking and operating the chain brake” section in this manual for WARNING! Use only original manufacturer’s replacement additional information. saw. parts, accessories, and attachments. Failure to do so can cause MAINTENANCE SCHEDULE possible injury, can contribute to poor performance, and may void your warranty.
  • Page 32: Safety Devices

    position without assistance, take the product to an authorised that cold weather is a major factor contributing to Raynaud’s Syndrome. service centre for repair prior to use. Indi ■ After each period of operation, exercise to increase blood circulation. SYMBOLS ■...
  • Page 33 WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. CAUTION Without safety alert symbol Indicates a situation that may result in property damage. ally will...
  • Page 36 Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC, 3149, Australia Techtronic Industries N.Z. Limited AEG is a registered trade mark used under Unit C, 70 Business Parade South, license from AB Electrolux (publ). Highbrook, Auckland 2013, New Zealand POWERFIT is a trade mark of Techtronic Outdoor Products Technology Limited in ANZ.

Table of Contents