Page 1
Service Manual is STRICTLY PROHIBITED unless you have obtained the prior written consent of the LG Electronics entity from which you received this Service Manual. The material covered by this prohibition includes, without limitation, any text, graphics or logos in this Service Manual.
Page 15
Note) Refer to ECO about detail of revision history. LG electronics...
Page 16
LG ELECTRONICS INC. / MONITOR DIVISION Establish : 2019/03/29 LM61C ADJUSTMENT SPECIFICATION 3/11 Revision : 1 CONTENTS 1. Application 2. Designation 3. Main PCB check process 4. Total Assembly line process 5. Shipping condition 6. Signal composition for adjustment LG electronics...
Page 17
LG ELECTRONICS INC. / MONITOR DIVISION Establish : 2019/03/29 LM61C ADJUSTMENT SPECIFICATION 4/11 Revision : 1 1. Application 1.1 This document is applied to LM61C chassis 27GL850 LCD Monitor which is manufactured in Monitor Factory or is produced on the basis of this data. 1.2 Manufacturing Type: SET 1.3 Panel name : LM270WQA‐SSA1 2. Designation 2.1 The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing. 2.2. Power Adjustment: Free Voltage 2.3. Magnetic Field Condition: Nil. 2.4. Input signal Unit: Product Specification Standard 2.5. Reserve after operation: Above 5 Minutes (Heat Run) Temperature : at 25℃±5°C / Relative humidity: 65 ±10% / Input voltage: 100 ~ 240V, 50/60Hz 2.6. Adjustment equipments: Color Analyzer (CA‐210 or CA‐110, UA‐10), DDC Adjustment Jig equipment, 3. Main PCB check process After Manual‐Insult, executing APC * APC ‐ 3.1 ADC Process ‐ GL850 doesn’t need ADC process because it has only digital input like DisplayPort, HDMI. 3.2 Main PCB Function test ‐ Check display/audio according to interface ...
Page 18
Save Warm(6500K) Color by commanding COLOR SAVE Command code. (tolerance ±0.010) Insert HDMI Jack which is connected with PC for White Balance or equivalent device. Total Assembly line should check whether the color coordinate(x,y) data refer to below table were meet or not. LG electronics...
Page 19
※ When doing Adjustment, Please make circumstance as below. 4.3 DPM Operation check ■ Measurement Condition: 100~240V@ 50/60Hz 1) Set Input to DisplayPort, HDMI1, HDMI2 2) Turn off the source device. 3) Check DPM operation refer to the below table. Sync (H/V) EUT Operating Condition LED(SET) Wattage(W) or Video (MSPG6100) Sleep mode Off/Off Off Off 0.5W DC Switch Off Off mode ‐ ‐ Off 0.3W 5. Shipping condition Make sure to do FACTORY RESET at the final process. LG electronics...
Page 20
Full Wide Language Depend on the sale region SMART ENERGY Low SAVING Power LED Automatic Standby Off(EU/EK/PD/EW/MA,4H) HDMI Compatibility Off General Mode DisplayPort 1.4 Enable Depend on signal OSD Lock Serial Number, Information Total Power On Time Resolution Reset 6. Signal composition for adjustment 6.1 I2C (100K BPS) LG electronics...
Page 21
00 9300K Aging off &Clear elapsed 11 Elapsed time Clear E9 00 00 time Start White Balance 12 WHITEBALANCE_START ED 00 adjustment (Display Internal Pattern) 13 Aging On/Off FF/00 FF:ON / 00:OFF 1:DisplayPort 0xD0 14 Input Select F4 00 0x90 2:HDMI1 3:HDMI2 0x91 15 SYSTEM RESET F5 00 00 Restart System LG electronics...
Page 22
24 byte Module selection LM270WQA-SSA1 22 6.5. EEPROM Data Write 6.5.1 Siganl TABLE START 84+n ADL A Data_1 . . . Data_n STOP Delay 20m LEN : 84h+Bytes CMD : E8h LG electronics...
Page 24
D : data 8‐byte write START A Data1 A …. Data8 STOP L : 0x00,0x10,….0x70 6.6.5 EDID Read DDC2B Command.(A0/A1) START START Data1 . . . Data128 STOP ‐ 128 Byte transfer of EDID Buffer of MICOM LG electronics...