Advertisement
insulation extends beyond the cable restraint and that the
restraint is tight. Double insulated products, which are always
marked with this symbol
neutral (blue) wires only.
DO NOT connect either wire to the earth terminal.
1.3
BATTERY SAFETY INSTRUCTIONS.
WARNING! Battery contains lithium-ion which is dangerous.
Handle with care to avoid damage, fire, corrosion or personal
injury.
Charge battery prior to its first use. the battery will have
been shipped in a low charge state.
WARNING! To reduce the risk of burns or fire:
DO NOT Attempt to open, disassemble, modify or service the
battery pack.
DO NOT Crush, puncture, short external contacts or dispose of
in fire or water.
DO NOT Expose to temperatures above 40°C (104°).
Replace only with the battery pack designated for this product.
Recycle or dispose of used battery as stipulated by local
regulation.
Use only the charging base provided to charge the wrench battery.
DO NOT attempt recharging the battery by means of an engine
generator or a DC power source.
WARNING! Dispose of spent batteries correctly as they contain
Lithium-ion. DANGER! DO NOT attempt to disassemble the
battery. For safety and environmental reasons DO NOT discard
in domestic waste or by burning. ONLY discard or recycle
according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your
person. If you come into contact with battery liquid take the
following immediate action:
a) Skin contact: Wash immediately with soap and water,
then wash flesh in either lemon juice or vinegar.
b) Eye contact: Wash with a strong solution of boric acid,
and seek immediate medical attention.
2. INTRODUCTION & SPECIFICATIONS
Powerful cordless impact wrench with forward, reverse and trigger
lock control. Produces torque in excess of 407Nm (300lb.ft) - enough
to remove wheel nuts. Soft grip handle for added comfort and
control. Powered by lithium-ion battery (sold separately, order Model
No. CP50BP), which maintains a high energy density level with a flat
discharge curve - performing better and longer than a conventional
Ni-CD/Ni-MH battery. No memory effect allows the battery to recover
from a deep discharge with no tendency to reduce overall capacity.
Requires 1 hour mains charger (sold separately, order Model No.
CP50MC).
Battery: .............................................................................. 18V - 2.6Ah
Drive size: ......................................................................... 1/2"Sq Drive
Maximum tourque: ....................................................... 407Nm/300lb.ft
No Load Speed: ..................................................................... 2200rpm
Impact Rate: .......................................................................... 2000bpm
Weight: .......................................................................................2.25kg
Battery Model No. (not included):............................................CP50BP
Mains Charger Model No. (not included): ..............................CP50MC
Noise Power: ..............................................................................97dBA
Noise Pressure: ..........................................................................86dBA
Vibration: ................................................................................ 4.63m/s²
3. CHARGING
CHARGING THE BATTERY (NOT INCLUDED, ORDER
MODEL No: CP50BP)
Note: When new, the battery will have been shipped in a low charge
state. Fully charge the battery before using your tool
3.1
to remove the battery from the Impact wrench, depress the two
side clips on the battery. DO NOT touch the metal battery
terminals.
3.2
take the base charger (Not included, order model No:
CP50MC) and plug it into the mains.
3.3
the battery is designed to fit into the charger one way
only. this is to ensure that the positive (+) and negative (-)
polarities correspond. Insert the battery and press lightly to
seat the battery firmly into the charging base, as in fig.1.
WARNING! DO NOT try to force battery into the base the
wrong way around.
,are fitted with live (brown) and
Original Language Version
3.4
When the charger is plugged into the mains the Green led will
illuminate.
3.5
When the battery is inserted into the charger the red LED
(fig.1) will begin to flash, this indicates the battery is charging.
3.6
When the red LED (fig.1) stops flashing and is solid the
battery is fully charged.
3.7
If when inserting the battery the red LED (fig.1) does not
illuminate the battery is already fully charged.
3.8
Switch off and remove the plug from the mains. Remove the
battery from the charger. Insert the battery back into the impact
wrench (fig.2) until it snaps into place. the wrench is now
ready for use.
3.9
to check charge state of battery depress button on top of the
battery pack, the lights will illuminate to indicate how
much charge is left in the battery.
4. OPERATION
4.1.
USING THE WRENCH
4.1.1. Use only impact sockets which are specifically designed for
use with an impact wrench.
4.1.2. Fit the socket to the wrench by snapping it onto the square
drive.
4.1.3. Fit the battery pack to the wrench.
4.1.4. Select the required direction of rotation. to change direction,
push Forward/Reverse button (fig.2) to the left or right.
Familiarise yourself with this operation before use. DO NOt
attempt to change the direction of rotation whilst trigger is
depressed. When the wrench is not in use, use the Forward/
Reverse button to lock off the trigger by placing the switch in
the middle position.
4.1.5. When tightening, release the trigger as soon as the impact
sound is heard. take care not to over-torque small fixings.
Note: On critical fixings always check the torque with a torque
wrench according to the vehicle manufacturer's, or
product, guidelines.
fig.1
CP5001
Issue: 1 - 13/05/10
Advertisement
