Advertisement
Quick Links
7" FLAT PANEL COLOR OBSERVATION
MONITOR OWNER'S MANUAL
AOM703 Features:
– 7" High Performance Color LCD Monitor
– Water Resistant Design
– Built-in Audio Speaker with Volume Control
and 12V Trigger
– 3 Camera (A/V) Input with Source Select Control
– Backlit Controls and Day/Night Picture Modes
for Nighttime Use
– Auto/Manual Power On
– Sun Visor Included
UDIOVOX
PECIALIZED
PPLICATIONS, L.L.C.
AOM703
S
S
Visit us at http://www.asaelectronics.com
Patent Pending
+
–
Advertisement
Related Manuals for ASA Electronics oyage AOM703
Summary of Contents for ASA Electronics oyage AOM703
- Page 1 7” FLAT PANEL COLOR OBSERVATION MONITOR OWNER'S MANUAL AOM703 Features: – 7” High Performance Color LCD Monitor – Water Resistant Design – Built-in Audio Speaker with Volume Control and 12V Trigger – 3 Camera (A/V) Input with Source Select Control –...
- Page 2 Important! – Please Read This Manual Before Installing! Congratulations on your purchase of a Voyager AOM703 LCD Observation Monitor. With proper installation and use, your AOM703 is designed to provide you with years of trouble-free operation. This manual contains important information required to properly install and operate the unit.
- Page 3 PACKING CONTENTS: 90 DAY/ 12 MONTH LIMITED WARRANTY SPLIT GROMMET DISTANCE MARKER 1” O.D. 3/16 I.D. STICKER QTY. 1 QTY.1 4” BLACK WIRE TIE QTY. 4...
-
Page 4: Controls And Operation
Stand-By mode -Turned on by a stand-by trigger wire generally connected to the vehicles 12V reverse back up lights or turn signals. Manual Mode wiring - For manual mode operation, the AOM703 should be wired as follows: ACC (12V+) Red wire should be connected to the vehicles accessory feed. - Page 5 These buttons also serve as adjustment controls while in the Picture Adjustment Menu mode (see above section for details). *Note: The AOM703 requires +12V to be applied to the “Audio Enable” trigger input in order to activate the built-in speaker. If no audio output is heard from the...
-
Page 6: Installation Instructions
11. Install the PanaVise® mount to the LCD monitor using the #10 self-drilling screws (included). **Important: Do not use screws other than those provided with the AOM703. Void of warranty and serious product damage will occur. - Page 7 5’ intermediate cable included with the AOM703 to connect the monitor to the junction box. If more cable length is needed, additional 5’ lengths of the intermediate cable can be purchased. (See the accessory list at the back of this manual for part number details.)
- Page 9 REAR OBSERVATION INSTALLATION DISTANCE MARKER USE/INSTALLATION FIGURE A FIGURE B - PLACE INDICATOR MARKERS (CONE, BOX ANY REFERENCE OBJECT HANDY) BEHIND VEHICLE AS IN FIGURE A. - PLACE RANGE MARKER DECALS ON SCREEN OF MONITOR OVER IMAGE OF INDICATOR MARKERS ON GROUND BEHIND VEHICLE, AS VIEWED ON THE MONITOR SCREEN.
- Page 10 10mm JUNCTION BOX MOUNTING TEMPLATE 10mm 30.4mm 14.8mm 60mm...
- Page 11 ® PANAVISE MOUNT TEMPLATE (OPTIONAL ACCESSORY) 0.25 0.25 2.00 2.50 2.00 0.25 2.50...
-
Page 12: Troubleshooting
SYMPTOM No power No +12V accessory, No ground, mis-wired/reversed Video/No audio White audio trigger wire not powered, Volume adjust Monitor does not Blue standby wire not powered activate in Standby reverse trigger Negative/dark Low voltage, Brightness video image adjustment down No video/no audio Camera connection Vehicle battery... -
Page 13: Product Specifications
PRODUCT SPECIFICATIONS LCD panel specifications: Size/Type 7” (diagonal) /TFT LCD Brightness 350 nit (min) 420 nit (typ.) Contrast Ratio 200 (min) 300 (typ.) View Angles Top (12 o’clock): (@ CR 10) Bottom (6 o’clock): 50 (min) Horizontal: Response Time Rise: 12ms (typ.) ; 50ms (max) Fall: 18ms (typ.) ;...