Page 1
P P P P P P THE ORIGINAL PECO PECO PECO PECO PECO POWER SPRAYER Model# 12008 PS5 Power Sprayer OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE Initial Release - Sept 2021 MANUAL PART#: Q0582...
6. REMEDIED EXCLUSIVE: The only remedies the purchaser has in connection with the breach or performance of any warranty on New PECO, Inc. consumer products are set forth above. In no event will New PECO, Inc. be liable for special incidental or consequential damages.
Handle for easy Transport & Storage No need for pumping or lugging with the all new PS5 40psi Electric Pump runs up to 6 hours on a single Power Sprayer. It’s completely self-contained and rolls charge easily over lawns and through gardens.
Section II - INSTALLATION FOR USE Sprayer Pump Installation Align and position the Sprayer Pump (Item #2) to the (4) mount holes on the Chassis Body (Item #1) as shown in Figure A. Secure the Sprayer Pump by using (4) #10-12 Flat Tinnerman Nuts (Item #3) and (4) #10-12 x 3/4” Blunt Tip Sheet Metal Screws (Item #4).
Component Back Installation Once your Sprayer Pump & Power Sprayer Battery has been installed, install the aluminum Component Back (Item #2) to the Chassis Body (Item #1). First, locate all bolt holes on the edge of both parts and install (12) Small Tinnerman Clips (Item #4). See Figure A. Next, align the Component Back to the Chassis Body by aligning the (2) bottom bolt holes to those on the Chassis Body and securing the Component Back by using (2) #10-12 x 1/2”...
Component Top Installation With the pre-installed Tinnerman Clip (Item #4) onto the Chassis Body (Item #1) and the Component Back (Item #2), install the Aluminum Component Top (Item #3) by aligning the Top over the Chassis Body and the Component Back by securing the Top by using (4) #10-12 x 1/2”...
Power Sprayer Handle Assembly Installation Before installing the Power Sprayer Handle Assembly (Item #1), install (2) Locator Pin Nuts (Item #3) to either side of the Chassis by using (2) 1/4”-20 x 1/2” HHCS (Item #4). See Figure A. Once the Locator Pin Nuts have been installed, position the Chassis Brace (Item #2) between the Left & Right Chassis as seen in Figure B.
Power Sprayer Handle Assembly Adjustment The Power Sprayer Handle Assembly P#(A2377) position can be adjusted to lower or raise the Handle by moving the (2) Locator Pin Nuts P#(B4251) to the different set of holes. See Figure A below. Note: Some parts and part features have been hidden from view for visual clarity. Figure A Locator Pin Handle Assembly...
29” Stainless Steel Sprayer Wand Assembly Your Stainless Steel Sprayer Wand Assembly will come installed with a standard Flat Nozzle (Item #2), there will be a secondary Elbow Nozzle P#(J1205) available as shown in Figure B. When switching out your Sprayer Nozzle, you can store whichever one you’re not using onto the Chassis Brace as shown in Figure C.
SAFETY DECALS To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. (1) R0056 Decal / Designed &...
Service Center will be happy to supply replacement to the battery. parts, accessories, and do any service or repairs to your PECO Power Sprayer. If for any reason your Service The battery life span is approximately 200 charges. Center is unable to service your PECO Power Sprayer or supply replacement parts, contact PECO and include the following information on the chart below.
Viton Chemical Compatibility Your Power Sprayer comes equipped with Viton Valves. Viton is a synthetic rubber that resists many hydrocarbons, biodiesel and petro chemicals, but it is NOT compatible with ketones. DO NOT use substances such as acetone, esters, amines, organic acids, acetic acid, methyl ethyl ketone (MEK), ethyl acetate, etc. Use the chart below as reference to determine which chemical maybe compatible with your Power Sprayer.
The Drift Guard can be easily adapted to the end of your Sprayer Wand. See the Figure below. The Drift Guard P#(J1207) is available for purchase, please contact New PECO, Inc. to request more info or to place an order.
Page 22
P P P P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...