Conglom QT014 Installation And Repair Manual

High efficiency dual flush toilet
Before beginning installation, read ALL instructions first. Save these instructions
for future use. IF THERE ARE ANY PROBLEMS WITH INSTALLATION OR
OPERATION, DO NOT RETURN TO STORE. PLEASE FIRST CALL CUSTOMER
SERVICE AT 1-877-333-0098 (Monday to Friday, 8:30am to 5:00pm, EST)
• Observe all local plumbing and building codes.
• Carefully inspect the new toilet and components for damage.
• If the existing toilet installation area does not have a supply shut-off valve (see
Fig. 9) below the tank, you will need to install one before installing the new toilet.
• Ceramic toilets are very fragile, so please handle your new toilet with extra care
during installation.
• Once the toilet is removed from the packaging, always ensure it is placed on a
soft surface such as a towel or blanket before installation.
INSTALLATION
Tools required for assembly: Safety goggles, hack-
saw, level, putty knife, adjustable wrench.
1. Check to make sure that the top surface of the
(not supplied) (see Fig. 1) is above the plane of
the surface on which the bowl will be installed. If the
is below the surface due to any reason
(i.e. marble or ceramic tiles, or improper installation,
etc.), then you will have to put on the outlet seal "I"
(see Fig. 2) that is thick enough to create a proper seal.
Note: A professional plumber is recommended for this
type of installation.
2. Turn the toilet bowl upside-down and rest it gently on the
on something soft (i.e. a towel or piece of cardboard).
Then center the wax side of the outlet seal "I" over the toilet
bowl outlet and push it down around the bowl outlet
(see Fig. 2).
3. Place bolts "AA" in
in place with the disk nuts "BB" to hold them in place
while installing the bowl (see Fig. 3).
4. Lift the toilet bowl, turning it right-side up, and lower it
over the while having the
"AA" come through the mounting holes of the bowl.
Then push down and twist the toilet bowl until it is
touching the and ensuring a proper seal of the toilet
bowl outlet with the Be careful not to damage
the around the bottom of the toilet bowl (see Fig. 4).
5. If required, place shims (not supplied) under the base of
the toilet bowl to prevent any rocking of the toilet bowl on
the (see Fig. 5b). On both sides of the bowl, place the
bolt cap bases "H", bolt washers "DD", and
the nuts "CC" onto the
Alternately tighten the
of turns each until snug. DO NOT OVER TIGHTEN. Snap
the bolt cap "G" onto the bolt cap base "H" (see Fig. 5a).
Note: If the bolts "AA" are too long, then cut
the top of the bolt with a hack saw to make room for the
bolt cap to snap into place (be careful not to damage the
ceramic while cutting). If desired, place a bead of caulking
(not supplied) around the base of the toilet bowl where it
contacts the (see Fig. 5b).
Floor
Floor flange
Floor
flange
securing them
bolts
bolts "AA". Floor
mounting
holes
nuts "CC" by a couple
I N S TA L L AT I O N | R E PA I R | C A R E | W A R R A N T Y
6. DUAL FLUSH BUTTON INSTALLATION
(i) Push button installation: The dual
tank in a separate plastic bag and will need to be installed on the tank cover. Open
bag and carefully remove contents.
• Insert button mechanism through tank lid (see Fig. 6). The buttons should be
rotated so the smaller button is on the left.
• Securely tighten nut. DO NOT OVER TIGHTEN.
Fig. 1
(ii) Push rod adjustment: To ensure both buttons
each push rod must be
the rods are not with the top surface, adjust the length of each rod by turning
the adjustment nut on each push rod (see Fig. 7).
Fig. 2
DUAL FLUSH VALVE TROUBLE SHOOTING
Fig. 3
Flush volume
If the push rods are too short and not fully connecting with the
sult in low volume. Readjust push rod height and ensure the bottom of the push rod
is with the top surface of the valve cylinder (see instruction ii, Fig. 7).
Flush valve leaking
If the push rods are too long, this may result in the
with the adjustments nuts (see instruction ii, Fig. 7).
Fig. 4
Tank leaking from the valve (and for maintenance and cleaning)
To clean the valve seal or replace the entire unit:
• Turn cylinder counter clockwise and lift off
• Clean the bottom of the
• Reverse this procedure to attach
Fig. 5a
Fig. 5b
1
button mechanism will be shipped inside the
the toilet correctly, the bottom of
with the top surface area of the
Valve cylinder surface
valve leaking. Shorten push rods
valve seal and the top of the valve seat
valve cylinder (see Fig. 8)
Flush valve seal
Flush
valve
seat
QT014
Fig. 6
valve cylinders. If
Fig. 7
valves, this may re-
Fig. 8