1. Manuals
  2. Brands
  3. Gooch & Housego Manuals
  4. Control Unit
  5. MLPXXX-YDC
  6. Operating manual

Gooch & Housego MLPXXX-YDC Operating Manual

Digital driver module
Hide thumbs

Advertisement

Table of Contents

OPERATING MANUAL
DIGITAL DRIVER MODULE
MODEL NUMBER:
MLPXXX-YDC
Former Model Number: 21XXX-YDM
DOCUMENT NUMBER: 51A14095B
This Operating Manual is for use with AOM Drivers with model numbers:
XXX = a fixed frequency of between 27 and 300 MHz crystal controlled.
Y = 0.4, 1, or 2 Watts output
D = Digital Modulation
C = Contact Cooled OEM Module
For More Information, Contact: Sales@goochandhousego.comwww.goochandhousego.com
As part of our policy of continuous product improvement we reserve the right to change specifications at any time.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MLPXXX-YDC and is the answer not in the manual?

Questions and answers

Summary of Contents for Gooch & Housego MLPXXX-YDC

  • Page 1 OPERATING MANUAL DIGITAL DRIVER MODULE MODEL NUMBER: MLPXXX-YDC Former Model Number: 21XXX-YDM DOCUMENT NUMBER: 51A14095B This Operating Manual is for use with AOM Drivers with model numbers: XXX = a fixed frequency of between 27 and 300 MHz crystal controlled.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Section Description Page INSPECTION PROCEDURE DESCRIPTION III. SPECIFICATIONS OUTLINE DRAWING CONTROLS AND CONNECTIONS TESTING PROCEDURE OPERATING PROCEDURE 51A14095B.doc 2 of 9...

  • Page 3: Inspection Procedure

    SECTION I INSPECTION PROCEDURE Examine the shipping carton for damage. If the shipping carton or packing material is damaged it should be kept for the carrier’s inspection. Check the contents of the shipment for completeness, mechanical damage, and then test the equipment electronically. Operating procedures are contained in Section VI.

  • Page 4: Description

    SECTION II. DESCRIPTION The model MLPXXX-YDC is a crystal controlled RF frequency generator designed to supply a signal of XXX MHz, where XXX is a fixed frequency of between 27 and 350 MHz, up to two Watts maximum output and is used to drive the Gooch and Housego 15000, 23000, 24000, 26000 free space series and fiber coupled series acousto optic modulators.

  • Page 5: Specifications

    SECTION III SPECIFICATIONS PARAMETER: SPECIFICATION: Output Frequency: XXX MHz Where XXX = a fixed frequency of between 20 and 350 Frequency Stability: + 0.01% Quartz Stabilized Spurious Levels: -50 dBc Maximum Harmonic Distortion: -15 dBc Maximum Digital Input: TTL Levels: TTL HIGH = Full RF Power TTL LOW = Minimum RF Power Output Frequency:...

  • Page 6: Outline Drawing

    SECTION IV OUTLINE DRAWING 51A14095B.doc 6 of 9...

  • Page 7: Controls And Connections

    SECTION V CONTROLS AND CONNECTIONS A. RF Out BNC - Female RF Power Output – The output is a factory set, crystal controlled, fixed frequency of between 20 and 350 MHz with an output power set nominally to 0.4, 1, or 2 Watts. When purchased with a Gooch and Housego AOM the output power will be set to give optimum performance.

  • Page 8: Testing Procedure

    SECTION VI TESTING PROCEDURES • With the power off, attach a 50 Ohm load capable of dissipating 2 Watts to the "RF Output" of the unit. Apply +24 Volts to the 24V INPUT solder post of the module and return to the Ground Lug. Apply a TTL High to the Modulation Input port through a 50 ohm cable.

  • Page 9: Operating Procedure

    OPERATION PROCEDURE: • The driver should be pre-set to output RF power at the required power level for the AOM. • With the power off, attach the Gooch and Housego 15000, 23000, 24000, or 26000 free space or fiber coupled acousto optic modulator or other acousto optic modulator device to the driver with a 50 Ohm cable.

Table of Contents