Advertisement
Functions
Motor torque for both:
Adjust the motor torque for both motors at ½ of the
total torque.
Power supply 230V:
Supply the control panel with 230V.Check that the yellow indication
light is ON. Press the button of the transmitter and check the red
indication light is ON. The first shutter move after power-up (230V)
is the OPEN direction, otherwise substitute open/close motor
wires.
Working time:
BOTH SECTIONS OF THE DOOR ARE FULLY CLOSED. Press
MOTOR TIMER button M1 and keep it pressed until the first door
section goes into the fully OPEN position, and leave it
immediately. Press MOTOR TIMER button M2 for the second
section of the swing door and also keep it pressed until the fully
OPEN position too. Remove power; place both sections in the fully
closed position and power up.
Motor direction
(open-close)
The MOTOR 1 (K7-8-9) is the motor that starts first from the
closure position of the gate. After all connections are completed,
move the both motors in the middle of the route manually. Power
the control panel with 230V. Using the button of timer M1 and
M2, check the indication lights to be ON. The movement of the
motors needs to be compatible with the function OPEN-CLOSE.
If not, turn the wires of the motor CLOSE-OPEN (K8/9) and
(K11/12). After all connections, close the gate manually. Turn
off and turn on the power of the control panel in order to
make RESET.
Slow move:
During the Open/Close tests, adjust the SLOW TIME so both
sections go to a fully open or close positions. The position
of the motor torque needs to be at ¼ of the turn.
External button:
1+2 activates both motors while external button 1 activates
ONLY the motor 1.
Photocell 2:
(Κ15) stops the gates' move immediately for how long the
photocell is activated.
Photocell 1:
(Κ17) works for protection and activates the auto-close.
When the door closes and the photocell beam is cut-off, the
door stops immediately and automatically activates the
open function. If the photocell beam is cut-off, the door
never closes. Auto close: Select dip-switch 4 to activate it.
There is a double counter in the A/C function. The first one
is 120 seconds and is applied when the door stops after an
open function. During this counting time of 120 sec., if the
:
Ag.Dimitriou 286A ,173 42 Agios Dimitrios
Call center: 210 9850 244, Fax: 210 9823 264
photocell beam is disturbed, then after the beam is free,
the A/C counting time becomes 10 sec. until the fully closed
position.
Motor delay:
Motor 1 starts first and after 3sec., starts Motor 2
Repeatable close:
Ιs used only in Hydraulic motors and activates instantly the
Slow close routine every 1H
Clear memory:
The first step is to clear the rolling code memory. Press the
button CODE of the controller and the RED light goes ON
after a while. Keep it pressed until the light goes off. The
memory is now clear.
Adding a new transmitter with the controller
button:
Press the CODE button and the RED light goes on (after a
small delay). Leave it and during the next 3 seconds, press
the desired transmitter channel button until the RED light
blinks and goes OFF. The new transmitter is saved. Follow
the same procedure to program more (up to 20 or 80) new
transmitters.
Adding a new transmitter remotely:
The motor is stopped. Press a working transmitter button
(already in memory) to start the motor working and hold it
pressed until the motor stops. When it stops, leave it and
press the new transmitter button immediately. The new
transmitter is saved. Repeat steps to program more
transmitters remotely. When the memory is full (20 or 80
transmitters) you cannot add more new transmitters.
Reset the automation:
Case of malfunction, please remove the power supply
(230Vac) for 10 seconds, reconnect and recheck.
Compatible
transmitters:
Based on the model you
have,
select
the
appropriate transmitter.
www.profelmnet.com
.
Advertisement
