Advertisement
3. SPECIFICATION
Model No: ........................................................... HVSF30.V2
Current: .........................................................................0.52A
Fan Diameter: .....................................................760mm(30")
Height: ............................................................ 1610-2030mm
Max. fan airflow rate (F): ....................................... 288m³/min
Fan power input: ...........................................................123W
Service value (SV): ......................................... 2.3(m³/min)/W
Standby power consumption (Psb): ...............................0.0W
Fan sound power level (Lwa): ................................... 70dB(A)
Max. air velocity (c): .................................................... 3.8m/s
4. OPERATION
4.1.
ASSEMBLY
4.1.1.
Remove all packaging material and check contents with the parts list.
4.1.2.
Bolt the outer tubular stand to the base using the fixings supplied.
4.1.3.
Slide the inner tubular stand into the outer tubular stand, fit and tighten the set knob to hold at desired height.
4.1.4.
Locate the motor housing onto the top of the inner tubular stand and fix in place using the nut, bolt and washers supplied.
4.1.5.
Place rear guard against the motor housing and fix in place using the 4 sets of nuts and washers.
4.1.6.
Slide the fan onto the shaft and tighten the fixing screw with a crosshead screwdriver.
4.1.7.
Hook the front guard into place at the top of the rear guard and then push the 7 clips around the edge of the guards into place so that
they engage both the front and rear guards.
4.2.
OPERATION
IMPORTANT: Ensure that all safety instructions from section 1 have been read and understood before using the fan.
4.2.1.
Set the fan on a level, dry surface.
4.2.2.
Plug the power cord into the mains supply.
4.2.3.
The fan features 3 speeds - selectable using the chain operated switch located at the back of the fan. This operates in a cycle -
OFF - LOW - MED - HIGH - OFF. LOW or MED settings will suit most needs, HIGH is used for maximum air movement.
4.2.4.
Adjust the direction of air flow up or down by loosening the knob and then tilting the fan assembly to the required angle, then re-tighten
the knob. To adjust the height setting, loosen the lower knob, set at desired height and then re-tighten knob. To oscillate the fan press
downwards on the knob on the top of the motor housing. To stop oscillation, pull the knob upwards.
4.2.5.
When not in use, disconnect from power supply and store in a safe, dry, childproof location.
5. MAINTENANCE
IMPORTANT: Turn the control switch to OFF and disconnect fan from power supply before cleaning.
5.1.
Use only a soft, damp cloth to clean the fan.
DO NOT submerse the fan in water and NEVER allow water to drip into the motor housing.
8
DO NOT use solvents or other chemicals to clean the fan.
8
5.2.
To clean the fan blades, loosen the 7 clips around the guards and then lift off the front guard from the top hook.
5.3.
Wipe the blades and guards.
5.4.
Reassemble by hooking the front guard into place at the top of the rear guard and then push the 7 clips back into place so that they
engage both the front and rear guards.
5.5.
Store the fan in its original box or otherwise cover the fan to protect it from dust.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
HVSF30.V2 Issue 2(3) 09/02/2021
Advertisement
