Advertisement
Quick Links
Advertisement
Related Manuals for Casio VM-1000
Summary of Contents for Casio VM-1000
- Page 1 (without price) VM-1000 (KX-661BXA) APR. 1999 INDEX...
-
Page 2: Table Of Contents
CONTENTS 1. SPECIFICATIONS ........................1 2. ADJUSTMENT ......................... 2 2-1. Adjustments to be done ....................2 2-2. Adjustments ........................2 3. PRINTED CIRCUIT BOARDS ....................6 4. EXPLODED VIEW ........................9 5. PARTS LIST ........................... 11 6. SCHEMATIC DIAGRAMS ...................... 15... -
Page 3: Specifications
1. SPECIFICATIONS Monitor (VM-102) Display Element: High-resolution color LCD Pixels: 224,640 (234 x 960) Driver: TFT active matrix Light Source: Internal backlight; high luminosity fluorescent lamp Speaker: One (3.6cm) round speaker Connection Cable: 16-pin RGB (Approximate Length: 2.5 m) Operating Temperature: 0°C to 40°C Storage Temperature: -20°C to 60°C... -
Page 4: Adjustment
2. ADJUSTMENTS 2-1. Adjustments to be done Adjustments Necessary equipment Adjusting block 1. VCC2 voltage adjustment Power supply, Digital multimeter (FD730C) Video unit 2. Contrast adjustment Power supply, Pattern generator, Signal generator, Oscilloscope Video unit 3. Tint, Color adjustments Power supply, Pattern generator, Signal generator, Oscilloscope Video unit 4. - Page 5 3. Tint/Color adjustment Video signal Oscilloscope 33kw CP313 Video Output Input CP337 1) Ground CP313 via 33k ohm resistor. 2) Unsolder (open circuit) IF pad HP200. Pulses 2 and 3 are adjusted by TINT While pulses 1 and 4 are controlled byCOLOR. 3) Apply 75% color bar signal to video input of the set.
- Page 6 6. VCO Free run adjustment CP757(VCC4-2) Set + monitor Power supply Frequency counter CP756 Input Output DC12V CP181 1) Adjust power supply voltage so that CP172 voltage becomes 11.5 ± 0.05V. 2) Connect CP756 and CP757 (VCC4-2). 3) Connect a frequency counter to CP181 and adjust VR751 so that the counter reading is 15.73 ± 0.1kHZ. 7.
- Page 7 9. Brightness adjustment Oscilloscope Pattern generator Set + monitor Output Input CP803~CP805 Video CP802 Trigger 1) Apply color bar signal to video input terminal. 2) Provide trigger pulse from CP802 to an oscilloscope. 3) Connect the oscilloscope to CP804 terminal. Observing the oscilloscope, 4.0 ±...
-
Page 8: Printed Circuit Boards
3. PRINTED CIRCUIT BOARDS 650A-M-A PCB — 6 —... - Page 9 661B-L PCB (Top View) NOTE : Parts in the gray areas are not used. — 7 —...
- Page 10 661B-L PCB (Bottom View) NOTE : Parts in the gray areas are not used. — 8 —...
-
Page 11: Exploded View
4. EXPLODED VIEW Video unit S3,S4 S3,S4 S3,S4 S3,S4 — 9 —... - Page 12 Monitor — 10 —...
-
Page 13: Parts List
5.PARTS PRICE LIST VM-1000 Monitor Item Code No. Parts Name Specification Q Price Code R 66100341 Name plate AM-K365 K440276A-1 66112010 Sensor cover AM-K660 K340585-2 66111980 Upper case AM-K660 K140268-2 66140180 Rating plate BXA-K661 K440824-6 27251349 TFT-LCD module COD55T5011RN 66112587 BLM ass'y... - Page 14 M PCB Item Code No. Parts Name Specification Q Price Code R Diodes D170 23901449 Chip schottky diode MA701A-(TX) D172 71011194 Chip diode MA111-(TX) D173 23602940 Chip zener diode MA3180-H(TX) D174 23901379 Chip schottky diode MA729-(TX) D176 23901379 Chip schottky diode MA729-(TX) D178 71011194 Chip diode...
- Page 15 Item Code No. Parts Name Specification Q Price Code R Q910 22530308 Chip transistor 2SD1119-R(TX) Q911 22530308 Chip transistor 2SD1119-R(TX) Q921 22510189 Chip transistor 2SB1218A-R(TX) Q922 22591540 Digital transistor DTC144EU-T106 Resistor R552 10147758 CDS P1201-01 Converter T160 30121491 DC/DC converter CST104-004 T900 30121484 Inverter converter...
- Page 16 Item Code No. Parts Name Specification Q Price Code R L310 30130693 Chip inductor MLF2012C150K-TP L350 30131015 Chip inductor NLC453232-100K-TP L600 30130917 Chip inductor NLC322522-100K-TP Transistors Q102 22510560 Transistor 2SB1261K Q104 22520588 Chip transistor 2SC2412K-T146R Q303 22501162 Chip transistor 2SA1576A-T106R Q304 22501162 Chip transistor 2SA1576A-T106R...
-
Page 17: Schematic Diagrams
6. SCHEMATIC DIAGRAM Monitor / M PCB — 15 —... - Page 18 Video unit / L PCB (1/2) NOTE : Parts in the gray areas are not used. — 16 —...
- Page 19 Video unit / L PCB (2/2) NOTE : Parts in the gray areas are not used. — 17 —...
- Page 20 CASIO TECHNO CO.,LTD. Overseas Service Division Nishi-Shinjuku Kimuraya Bldg. 1F 5-25, Nishi-Shinjuku 7-Chome Shinjuku-ku, Tokyo 160-0023, Japan...