This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any electronic or machine readable form without prior written permission of InnoLux Tech. Corp. Ltd. Acer B243HL Service Manual Table of Contents ...02...
When replacing parts or circuit boards, clamp the lead wires around terminals before soldering. Keep wires away from high voltage, high temperature components and sharp edges. Keep wires in their original position so as to reduce interference. Adjustment of this product please refers to the user’ manual. Important Safety Notice Acer –LCD-B243HL...
(Dutch, Finnish, Russian depend on sale region) : 1.8 m. (Black. Cord type depend on sale region) : 1.8 m. (15 pin D-SUB, black cable with blue male connector) : English (640Mb CD) : 1.8 m. (18+1 pin, black cable with white connector) Acer –LCD-B243HL...
+32°C/ 80% R.H., 12 hrs 12,000 feet at 25°C (hold 3.5 hrs) -30°C / humidity not controlled +25°C/ 50%R.H.(2hrs)-> -30°C/ No R.H.(12hrs).-> +41°C/ 90% R.H.(12hrs)->+65°C/ 10% R.H.(12 Hrs)->+25°C/ 50% R.H.(2hr) 39°C 40,000 feet at -30 °C (hold 1 hr) Acer –LCD-B243HL Specification...
Page 6
Energy Star ● Condition IEC61000-4-2(EN55024) Condition Spec Operating condition >15,000 Hours is 25°C Stable condition at 15,000 Hours(Typ) 25℃ Acer –LCD-B243HL Other ● ● Windows Windows ● Spec Contact discharge: 4KV Contact discharge: 8KV Air discharge : 8KV Air discharge...
Page 8
2.0 V (on) ≧ -0.3v ≤ V off ≤ 0.8 V (off) 30%~100% 1%~100% 42.9Vrms (Typ.), 44.2Vrms(Max) 20mA (Type.) 25mA (Max.) >75% Acer –LCD-B243HL Spec 60W ( min ) <output capacitor voltage Power ≤ 50W Blue < 2W Amber < 2W Amber <...
Page 9
: 25 ± 5°C : white : 1920 x 1080 : 700 mV ± 2% : 30 minutes Chromaticity Coordinate 9300K 0.283 ± 0.030 6500K 0.313 ± 0.030 Panel While x Acer –LCD-B243HL 0.297 ± 0.030 0.329 ± 0.030 Panel While y...
Page 10
Input impedance ﹕ ≧ 10K ohm 4.2.1 Frequency response range ﹕200Hz ~ 10kHz 4.2.2 4.3 USB in The USB 2.0 includes 4 pins: pin1:VBUS; pin2:DM; 4.4DVI-D in DVI-D Connector Pin assignment: luminance nine points luminance nine points pin3:DP; pin4:GND Acer –LCD-B243HL (backlight ≥ 75 (backlight...
Page 11
Red Ground Green Ground Blue Ground PC +3.3/+5V Sync. Ground DDC SDA H sync V sync DDC SCL Acer –LCD-B243HL Symbol Hot Plug Detect TMDS Data 0- TMDS Data 0+ TMDS Data 0/5 shield Clock shield Clock + Clock -...
Page 13
EDID File Format : VESA’s EDID Standard Version #3, Revision #0, EDID Structure EDID Data Table : See the attached table (for example) Specification : Version #1, Revision #3. Acer –LCD-B243HL TEST CONDITIONS THD+N = 10%﹐T 1KHz 1Vrms AT 1KHz 1Vrms Po≦ 2.0W...
Page 16
Color AUTO MENU ◄ ► POWER FACTORY ● MODE HOT KEY OPERATION Acer –LCD-B243HL DESCRIPTION Press [e], and then press [POWER] for DC power on. OSD menu will be shown with “F” on the left top. Select “F” for entering factory mode.
The On-Screen Display (OSD) shall be an easy to use icon based menu through keypad OSD buttons or remote control unit. The unit shall leave the factory with all OSD controls set to their default values. First ACER eColor Management Brightness User Focus...
Page 18
FW IC, which should be correspondent with that of PCBA FW IC. Double click Figure One. Manufacturer of Scaler is Mstar) One port of ISP program card is connected to PC print port. Acer –LCD-B243HL Full Full ETL000….0000(22)
Page 19
Acer FW IC Model Secondly ﹐ download FW software: first select “READ”, and then load FW software in Rooter (Fig.2). Software Checksum Thirdly, select “Connect” and enter ISP MODE as in the following Figure 3. Acer –LCD-B243HL FW software rooter...
Page 20
Acer Acer –LCD-B243HL Fourthly, select “AUTO”, and keep its default value. Click “RUN” for beginning programming. There will be prompting if programming is OK. Note: if programming fails or success rate is not high, click “Config” and adjust its speed in...
Page 21
Acer Acer –LCD-B243HL After connecting, AC ON, DC ON ◆Flowing chart Open ISP program Choose manufacturer and model of FW IC LOAD FW software Click Connect and enter ISP MODE Choose Config Click AUTO and RUN for and adjust beginning programming...
3.2. LCD Exploded drawing (All) 03 Exploded Diagram Fixed Description T(kg*cm 3.75±0.25 4.0±0.25 10.5 ± 0.25 9.0 ± 0.25 6.0±0.25 3.75±0.25 Acer –LCD-B243HL Remark FOR POWER D-SUB CON&DVI For back-cover to STAND ASSY For hinge to stand-BACK Plate base to Base FOR POWER&IF...
Item Place panel Assemble Keypad Pad and Bezel Assemble front bezel Acer –LCD-B243HL 7.0 Assembly and Disassembly Photo Procedures 1.Take panel out of box and place it on the foam; 2.Tear open the PE bag and put it in the designated carton;...
Page 58
Fix USB board mainboard and power board Acer –LCD-B243HL Assembly and Disassembly (continue) Insert IPC electric foam on the chassis like 1.Place the chassis on the cushion the attached after check, like the attached picture. 2.Insert power board into the designated location of chassis,like the attached picture.
Page 59
Fix chassis Insert FFCcable Insert lamp wire Acer –LCD-B243HL Assembly and Disassembly (continue) 1. Handle hexagonal screws and electric opener; 2. Twist screw in the interface as attached picture; 3. Place cushion on the designated location after iron frame is taken away.
Page 60
Assemble back cover Fix stand Packing Acer –LCD-B243HL 1.insert the speaker cable into the PIN location of chassis like the attached picture 2.be sure the red cable is on the left and the green one is on the right.