Advertisement
Quick Links
Advertisement
Summary of Contents for Simply Automated UPP
- Page 1 Pocket Programmer Model UPP UPB Pocket Programmer User Guide...
-
Page 2: Important Safety Instructions
No data is stored in the UPP. The UPB network and device programming is stored in each UPB device. A UPB network that was configured with the UPP may be added to UPStart at any time by using the Network Discovery feature in UPStart. The UPP... -
Page 3: Installation
INSTALLATION The Pocket Programmer is designed for indoor use. Simply plug the appropriate end of the provided AC cord into the top of the UPP, the other end into any 120-volt outlet anywhere in the house. Once the Pocket Programmer completes its start up procedure the top two (of six) selections of the main menu are on the display and it is ready for use. -
Page 4: Menu Navigation
The pocket programmer mirrors the functionality of UPStart Configuration software. If the installer is familiar with UPStart then most of the UPP menus and functions are intuitive and easy to use. If there are any questions or difficulties in using the UPP referencing the specific function in the UPStart software is highly recommended. - Page 5 Pocket Programmer Model UPP Access Network is used on an installed UPB network. It is useful when viewing or editing devices. Devices can be added or deleted. Links may also be added or deleted. The same functions are available in UPStart under the...
- Page 6 0 – 9 and A – F. Once the UPB network is created devices and Links may be added. Nothing is stored in the UPP. All data is stored in the devices as they are added. UPB device must share the same UPB Network ID and password to communicate peer to peer.
- Page 7 Pocket Programmer Model UPP Add Device is used to add installed UPB devices to the UPB network. If a device is not found: Make sure there is only one device in set up mode. Check the wiring to ensure the connections are proper and the wire nuts are on tight.
- Page 8 Pocket Programmer Model UPP Edit Device is used to change the settings on a previously added device. For instance, the dimming can be disabled under the Options sub-menu. - 8 -...
- Page 9 Pocket Programmer Model UPP...
- Page 10 Pocket Programmer Model UPP...
- Page 11 Link Actuator On/Off Button Toggle Button Drape Close Super Multi-Button Drape Open Multi-Button Null Button Panic Button BtmSuperRocker Bottom Rocker TopSuperRocker Top Rocker Indicator Off Dim Button Indicator On Bright Button Status Button On Button On/Off Button Off Button Model UPP...
- Page 12 Pocket Programmer Model UPP...
- Page 13 Transmit Type= <ENTER> <UP/DOWN> Link Direct TX Attempts=2 1 to 4 <ENTER> <UP/DOWN> Xmit to Repeatr: Xmit to Repeatr: <ENTER> <UP/DOWN> No Repeater Repeater, Tx=1 <UP/DOWN> Tx=1 to 3 Model UPP <MENU> <Writing> <ENTER> <MENU> <Writing> <ENTER> <MENU> <Writing> <ENTER>...
- Page 14 ELSE <SAI UML> Device Not Found If device is not found <ENTER> <MENU> 1)ID Go to Edit/View 2)Receive Links <ENTER> Device Sub-Menu <UP/DOWN> 1)ID 2)Receive Links <UP/DOWN> 2)Receive Links 3)Transmit Links <UP/DOWN> 3)Transmit Links 4)Options <UP/DOWN> 4)Options 5)Advanced Model UPP...
- Page 15 Device that is to have the Link added must be in Setup Mode. This feature will work with multiple devices as long as all are in Setup Mode This will display even if no device was put in Setup Mode, hence no Link added. Model UPP...
- Page 16 Pocket Programmer Model UPP...
- Page 17 9)Blink (Goto <ENTER> allows selection of level with <UP/DOWN> buttons. Fade UP/ STOP and Fade DOWN/STOP brighten or dim while holding the <ENTER> button and stop upon release) Model UPP To select <UP/DOWN> Network ID To select <UP/DOWN> Link ID Link = 001 <ENTER>...
- Page 18 Pocket Programmer Model UPP Smart Receive is used to observe UPB transmissions.
- Page 19 Pocket Programmer Model UPP...
- Page 20 Pocket Programmer Model UPP Simply Automated, Incorporated 5825 Avenida Encinas, Suite 101, Carlsbad, CA 92008 USA Technical Support: www.simply-automated.com or 800-630-9234 452-0031-0001 Rev. A Revised: May 16, 2006...
Need help?
Do you have a question about the UPP and is the answer not in the manual?
Questions and answers