Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NATDIS CleanMove 8
Summary of Contents for NATDIS CleanMove 8
- Page 1 CleanMove 8 Mounting and operating instructions...
-
Page 2: Table Of Contents
Index 1. Revision summary ....................................3 2. Hazard markings and safety signs ............................... 3 3. Equipment information ..................................4 3.1 Equipment purpose ..................................4 3.2 Definition of UVC-disinfection ............................... 4 3.4 About the documentation ................................4 3.5 Declaration of conformity ................................5 4. -
Page 3: Revision Summary
1. Revision summary Revision Date Comments/Changes 15-03-2021 Document created 2. Hazard markings and safety signs The following hazard markings are used on the equipment and have the following meaning: Danger of non-coherent radiation In this case UV light Attention: Protect eyes and skin against UVC light. Danger Electric current Attention:... -
Page 4: Equipment Information
3. Equipment information 3.1 Equipment purpose The UV equipment is constructed to treat all light-accessible surfaces in the selected area in a chosen timeframe and area. 3.2 Definition of UVC-disinfection: UVC unit is dimensioned to deliver a dose of (as per by agreement) J / m2 on all light-accessible surfaces after a full cycle of the time (by agreement). -
Page 5: Declaration Of Conformity
DS/EN 619 + A1:2010 Continuous transport equipment and systems - Safety and EMC requirements for equipment for mechanical transport of general cargo Meets the following EU guidelines: EU- Machinery Directive 2006/42/EC EU- Low voltage directive 2006/95/EF EMC-guidelines 2014/30/EU Haderslev 02/2021 Pernille Snitkjær, CEO, NATDIS ApS, Brunbjerg 70, 6100 Haderslev... -
Page 6: Equipment Overview
4. Equipment overview The UV unit contains of: CleanMove 8 for surface and air disinfection. 4.1 Environment for the equipment 4.1.1 Surface The installation must be placed on a flat surface without inclination and fastened according to the instructions. 4.1.2. Placement The equipment may only be used in places where the surface is level and can be securely fastened. -
Page 7: Connecting The Device
4.2.1 Connecting the device 1. Connect 230V power cable to the socket on the floor in the UV system. 2. Place the lamps in the desired position. 3. Make sure that no one is in the room with the UVC unit. 4. -
Page 8: About The Risk Using Uvc
5.2 About the risk using UVC: When using normal work clothes with full cover of skin and safety glasses, the risk of permanent damage from short-term exposure to UVC light is limited to the effect on the skin and the minimal risk of damage to the eyes. -
Page 9: Repeated Daily Dose Overruns
• Eyes, severe irritation 24-48 hours (severe cases of welding eyes, with short-term loss of vision) • Skin, severe redness like light to medium sunburn. In case of severe exceedance factor +10 Risk of: Eyes, permanent damage, impaired vision • Skin, Severe sunburn;... - Page 10 • The system is dismantled and sorted into categories as required by applicable environmental requirements. The installation is subject to Directive 2008/98 / EC and Directive 2002/96 / EC on waste. • When the system is obsolete, all existing components must be sorted and handed in at an •...
-
Page 11: Service And Maintenance
6. Service and maintenance Gloves should comply with: 2019-4121X. All service and maintenance must be performed without danger. System must be shut off and cooled down before service is performed. Access to bulb change or quartz glass change can be done by detaching lamps from fittings / clips. 6.1 Bulb change: 1. -
Page 12: Cleaning Of Uvc-Systems
Attention: Protect eyes and skin against UVC-light. Equipment supplied by NATDIS may only be cleaned when the system is switched off and in a safe condition. All work on UVC systems requires that the system is secured before work begins. -
Page 13: Dry Cleaning
7.3. Dry cleaning Dry cleaning includes a thorough vacuuming of the components. A vacuum cleaner equipped with a suitable filter for product and material residues must be used. Never wipe product dust off dry, and never use compressed air for dry cleaning, as product dust will not be removed via these methods;... -
Page 14: Liability And Warranty
a. Wipe UV tubes with a dry cloth (antistatic cloth or hard-wrung cloth) In connection with the cleaning, the UV equipment must be inspected for breaks and defects. Check the following: 1. The glass is intact without cracks and crushes. 2.
Need help?
Do you have a question about the CleanMove 8 and is the answer not in the manual?
Questions and answers