Advertisement
Quick Links
Advertisement
Summary of Contents for FlyWood CineRace20 ANALOG
- Page 1 FLYWOO CineRace20 ANALOG Base V1.0 CineRace20 ANALOG Base Manual...
- Page 2 FLYWOO CineRace20 ANALOG Base V1.0 1/ drone introduction CineRace20 a new concept and more than a cinewhoop . Inspired by RaceWhoop designed by Free Zillion. This is a combinathion of CineWhoop and RaceWhoop! CineRace is double duct design , not a simple guard anymore. . It can fly as flexible as a racing drone, and as stable as Cinewhoop.
- Page 3 FLYWOO CineRace20 ANALOG Base V1.0 Features 1. Almost all parts are injection molded. ABS\PC material. More sturdy and durable. 2. Very easy to disassemble and install, only fixed by two aluminum columns. 3. Pilots can freely combine their favorite colors to be more individual 4.
-
Page 4: Specification
FLYWOO CineRace20 ANALOG Base V1.0 Specification Item: CineRace20 Analog w/ Caddx Ant Weight: 93g (without battery) FC & ESC : GOKU GN 413 13A AIO Frame: CineRace20 Frame Kit Motors: NIN V2 1203PRO 3400Kv Props: Gemfan D51 -5 VTX: vtx625 450mw Antenna: Flywoo Circular RHCP 5.8Ghz Ant ( UFL-Length: 115mm \ Tube 45mm ) - Page 5 FLYWOO CineRace20 ANALOG Base V1.0 Highly recommended battery Explorer 4S HV 300mah Battery (You will get good flight time and fly quite flexible) Explorer 4S HV 900mah Battery (You will get a super long flight time, and the flight will...
- Page 6 FLYWOO CineRace20 ANALOG Base V1.0 PID and filter settings...
- Page 7 FLYWOO CineRace20 ANALOG Base V1.0 Default serial port settings UART1: ELRS/TBS/R9M/XM+/DSMX/SBUS receiver UART2: VTX IRX TX 3/ Receiver binding TBS NANO 915: When the USB is connected, the green light of the receiver flashes, and then bind according to the picture operation.
- Page 8 FLYWOO CineRace20 ANALOG Base V1.0 ELRS 2.4G RX: Bind procedure: - Supply power to the EL24E/EL24P rx, wait until the LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on...
- Page 9 FLYWOO CineRace20 ANALOG Base V1.0 2/ Insert the R9M TX module and write the firmware you need 3/ To write the firmware of the R9MM receiver, you need to remove the R9MM receiver, and then write the firmware by connecting to the S.PORT port.
- Page 10 FLYWOO CineRace20 ANALOG Base V1.0 XM+ receiver: 1/ Press the XM+ receiver button, USB power supply, the red and green lights are always 2/ The remote control turns on the binding mode, the green light flashes to indicate successful binding, turn off and restart 3-1/ Then set the corresponding serial port and receiver protocol to ensure the normal output of each channel of the receiver.
- Page 11 FLYWOO CineRace20 ANALOG Base V1.0 4/ Mode setting: Set the ARM switch and flight mode switch, AUX* corresponds to the remote control switch, and the yellow area mark is turned 5/ Motor test: Unload the propeller, test the rotation direction of the motor, turn on the safety switch, and test the rotation of the motors one by one.
- Page 12 FLYWOO CineRace20 ANALOG Base V1.0 2/ BF Configurator will display to enter DFU mode. If it does not enter DFU mode, it may be that the driver is not installed. The driver can be installed using IMPULSE RC software Driver software: https://impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe...
- Page 13 FLYWOO CineRace20 ANALOG Base V1.0 4/ After the connection is entered, it is a blank interface, you need to write CLI commands, Factory CLI LINK: https://flywoo.net/pages/manual 5/ If the command is not restarted after writing the command, please write SAVE and...
- Page 14 FLYWOO CineRace20 ANALOG Base V1.0 6/ Then all functions of FC return to normal.
- Page 15 FLYWOO CineRace20 ANALOG Base V1.0 7/ Configuration table...