Overview FGMM1000 Front Color Status Power Green 5G signal connected 5G signal not connected Blinking 5G and 4G LED blinking together means no SIM card detected 4G signal connected 4G signal not connected...
Blinking 5G and 4G LED blinking together means no SIM card detected WiFI Green WiFi enabled WiFi disabled Blink once New device connected Blink twice Device disconnected Bottom 1. Power port (12-24V DC IN) 2. RS232 serial port 3. RS485 serial port 4.
Setting Up: Basics Where to find more help In addition to this user guide, you can find help at Linksys.com/support/FGMM1000 (documentation, downloads, FAQs, technical support, live chat, forums) How to install your router 1. With power OFF, insert your SIM card in the slot on the back of the router until it clicks 2.
Page 7
Router Login On computer or mobile device connected to the router with an ethernet cable or via WiFi: 1. Enter http://192.168.100.1 in a web browser 2. Enter username/password to access router settings Login Username Password User user user Superuser administrator administrator 3.
Page 8
2. Place M3 screws and flat washers on both sides of the router as shown below. Align with Anchors and screw the router into the wall...
Back Bottom 1. Reset button (under screw cover) - Press and hold the reset button for 5 seconds to reset the router to factory default setting 2. 4G/5G signal indicator 3. LAN port LED 4. PoE (Power over Ethernet) port 5.
Setting Up: Basics Where to find more help In addition to this user guide, you can find help at Linksys.com/support/FGMM601 (documentation, downloads, FAQs, technical support, live chat, forums) How to install your router 1. Use a screwdriver to remove the SIM card slot cover and insert your SIM card 2.
Page 12
Router Login With a computer connected to the router with an ethernet cable: 1. Enter http://192.168.100.1 in a web browser 2. Enter username/password to access router settings Login Username Password Description User user user End User Superuser administrator administrator Advanced User 3.
Page 13
2. Tighten two M8 nut of mounting kit. 3. Adjust router antenna bearing and tilting to the desired angle, and then fasten 2pcs M8 nuts Pole Mounting Note: We recommend consulting with a qualified technician for pole mount installation. 1. Loosen 2 M8 long bolts/flat washers/spring washers/nuts, through the holes of back plate and the pole holder...
Page 14
2. Place washers and tighten nuts to secure the mounting kit...
Features Overview A snapshot of your router performance, settings and vital statistics. Check WAN (mobile network) and LAN (client devices) connections and view services that are running and data transfer statistics.
Connected Clients A list of the clients connected to your router, including the clients’ MAC address, IP address, and whether they’re connected wirelessly or with an ethernet cable. You can edit the device names to make them more easily identifiable.
Network Mobile Network Network Configuration Information about your network’s configuration, attachment status, and carrier identification and registration. Scan for carriers with service in your area. Mode Preference Choose your network mode and NR5G Standalone (SA)/Non-Standalone preference.
Automatically or manually set your APN settings (APN Name, PDN Type, APN Type, IP Allocation, Authorization Method, etc.) and create profiles. WiFi Settings (FGMM1000 only) View or edit your WiFi name and password or change other WiFi settings to fine-tune your network for your...
Firewall Settings Enable/disable IP address filtering and WAN port ping Access control lists can filter incoming or outgoing traffic and set rules defining how to forward or block that traffic at the router level.
Application Settings Routing Place this router’s modem into bridge mode when connecting to another router to avoid IP address conflicts. DHCP Server Edit LAN setting (host IP address and subnet mask) and configure your router as a DHCP server (DHCP range and lease time).
Page 21
Port Forwarding Configure your router to allow external devices use its LAN services. Port forwarding—for a single port, multiple ports or a range of ports—sends traffic inbound on a specific port or ports to a specific device on your network. Create an IP address to allow connected devices to access potentially risky external services without exposing the network to threats.
UPnP Settings Enable UPnP IDG to limit the service to only those devices that support IGD. Ser2Net (FGMM1000 only) RS323 to Network Connect devices with RS232 serial interfaces for reliable data transmission to other devices or network server applications.
RS485 to Network Connect devices with RS485 serial interfaces for reliable data transmission to other devices or network server applications. Enable Application Layer Gateway for SIP, TFTP or FTP to facilitate access for that traffic to specific clients.
Administration General Information about your router name, session timeout limit and network time protocol. Restore/Backup Create a configuration file or upload a file to restore your router settings.
Factory Reset Resets all router settings to factory defaults. You can restore settings if you saves a configuration file in the Restore/Backup screen. Firmware Update Set to automatic updates to keep your router up to date effortlessly. If you choose not to enable automatic updates, you can download firmware files and manually update.
System Reboot Restart your router to get begin fresh. All devices will be disconnected, but will automatically reconnect when the router is ready again – about 100 seconds.
About Descriptive identification information about your router.
Page 28
Specifications FGMM1000 Model Number FGMM1000 3GPP Standard 3GPP Rel 15 standard-compliant, Support both SA/NSA Radio Frequency WiFi 2.4GHz: Channel 1 – 11 5GHz: Channel 36, 40, 44, 48, 52, 56, 60, 64, 100,104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161...
Page 29
Specifications are subject to change without notice.
Page 30
Specifications are subject to change without notice. Linksys.com/support Third-party trademarks mentioned are the property of their respective owners. Licenses and notices for third party software used in this product may be viewed here: http://support.linksys.com/en- us/license. Please contact http://support.linksys.com/en-us/gplcodecenter for questions or GPL source code requests.