Dymec DY-HI8011-90bt User Manual

Hardened industrial 802.3bt gigabit poe injector, 1 x 10/100/1000m tx 90w pse + 1 x 10/100/1000m tx, 52-56 vdc input, operating temp.: -40c to +75c

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

DYMEC

User Manual-DY-HI8011-90bt

Hardened Industrial 802.3bt Gigabit POE Injector, 1 x 10/100/1000M TX 90W PSE + 1 x 10/100/1000M TX,

52-56 VDC input, Operating Temp.: -40°C to +75°C

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

operated

a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is lik ely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received; including interference that may

cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55032/24 class A for ITE, the essential protection requirement of

Council Directive 2014/30/EU on the approximation of the laws of the Member States

relating to electromagnetic compatibility.

DYMEC Inc. has an on-going policy of upgrading its products and it may be possible

that information in this document is not up-to-date. Please check with your local

distributors for the latest information. No part of this document can be copied or

reproduced in any form without written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

Table of Contents

Need help?

Do you have a question about the DY-HI8011-90bt and is the answer not in the manual?

Questions and answers

Summary of Contents for Dymec DY-HI8011-90bt

Page 1 Council Directive 2014/30/EU on the approximation of the laws of the Member States relating to electromagnetic compatibility. DYMEC Inc. has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information.
Page 2 DYMEC NOTE Always make sure the total length of the TX cable DOES NOT exceed 100meter. Total length is defined as length A + length B Remote Switch Length A + Length B < 100 meters POE signal attenuates every meter, the built-in transformer allows the attenuation to reach 100 meters to follow IEEE 802.3af/at/bt standards.
Page 3 DYMEC Installation package This unit can be din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted brackets are included. Power connection This unit provides a 4 pin terminal block. It can be operated using 52-56VDC power source. Always make sure your input voltage is within this supported voltage range.
Page 4 DYMEC LED indicator PW2 (Green) ON – Power is detected OFF – Power is not detected PW1 (Green) PoE (Amber) ON – PD is detected on designated port. ON – Power is detected OFF – no PD is detected OFF – Power is not detected...
Page 5 DYMEC Specifications IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3af for POE IEEE Standard IEEE 802.3at for POE+ IEEE 802.3bt Compliant with 60W uPoE standard Compliant with 95W Power over HDBaseT (PoH)
Page 6 DYMEC CISPR 32, FCC Part 15B Class A IEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV IEC 61000-4-4 EFT: Power: 2KV; Signal: 2KV IEC 61000-4-5 Surge: Power: 2KV; Signal: 2KV Vibration EN 60068-2-6 EN 60068-2-27 Shock Free Fall EN 60068-2-32...
Page 7 DYMEC Housing Dimension (mm) NOTE: Housing dimension is for purpose of showing product Length, Width, Height, din-rail, and terminal block’s position and dimension. Please reference the LED Indicator Page for correct port order.