Orava BN-45 Instruction Manual

Orava BN-45 Instruction Manual

Electric knife sharpener

Advertisement

Quick Links

Electric knife sharpener
BN-45
EN
Instruction manual
BN-45

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BN-45 and is the answer not in the manual?

Questions and answers

Summary of Contents for Orava BN-45

  • Page 1 Electric knife sharpener BN-45 Instruction manual BN-45...
  • Page 2 Do not use the tool to sharpen the blade of other types of tools/tools or tools. ORAVA Electrical Appliances are manufactured in accordance with the state of the art and recognized safety-technical rules. Nevertheless, the use or use contrary to designation may result in the risk of injury to or endangering the life of the user or third person, damage to the device and other material values.
  • Page 3 • This appliance is intended, in addition to domestic use, for the following uses: - in shops, offices and other similar work environments; - in economic buildings; - in hotels, motels and other residential environments; - in bed and breakfast establishments. •...
  • Page 4 1.3 Electrical safety • Before connecting the appliance to the power supply for the first time, make sure that the voltage on the appliance label corresponds to that of the household electrical outlet. • The electric appliance is designed to power from 1/N/PE ~ 230 V 50 Hz. •...
  • Page 5 • If the power cord is damaged, it must be replaced by the manufacturer, its service department or a similarly qualified person to avoid the risk of electric shock. • Regularly check and maintain the electrical appliance as well as the power cord and power socket.
  • Page 6 1.5 Cleaning, maintenance and repairs • Observe the normal user cleaning and maintenance of the appliance in the recommended way. Do not use solvents or harsh cleaners for cleaning. Pollution and visible stains from finger contact, respectively. The hands can be cleaned using detergent detergents specially designed to clean household appliances.
  • Page 7 2. Special Safety Instructions. Read carefully! Electrical equipment is designed and manufactured in such a way as to allow for safe operation and use by persons without a professional qualification. Despite all the measures that have been carried out by the manufacturer for safe use, handling and use, entails certain residual risks and associated potential hazards.
  • Page 8 Check/Startup • Carefully clean the machine before commissioning it, following the instructions in the „Startup“ section.„Cleaning and maintenance“. • Never clean the machine (its drive unit with electrical parts and controls) and the power cord with the plug in a way (under running water) that may cause the liquid to flow into the device.
  • Page 9 Operation/Supervision Please note! • The device is intended for grinding the blade edge. As the operator is handling a very sharp knife, always work with care and caution. • In case of careless handling: There is a risk of tearing or puncture of your fingers/hands! •...
  • Page 10 Warning! • After switching off the drive, the drive of the rotating parts will recharge for a certain amount of time. Always wait for the rotating parts to stop completely before handling the device. There is a risk of serious injury! •...
  • Page 11: Parts Descriptions

    Parts descriptions 1 coarse grinding wheel 2 fi ne grinding wheel 3 grooves for knife blade 4 power switch 0/I 5 container for the residue after grinding 6 adhesive cups Before fi rst use Do not plug the appliance into the mains during preparation. Unpack and remove all packaging material from it.
  • Page 12: Preparation And Operation

    Preparation and operation Location Disconnect the appliance from the power supply before locating it. Then lay it on and press it against a flat, firm surface so that the suction cups cling to the surface and the device firmly in place. For better adhe- sion, we recommend that the suction cups be slightly moistened before placement.
  • Page 13 Part 2: Part 2 is designed to fine-cut the knife blade to form a sharp blade. In- sert the knife completely with the handle and min. triple it evenly toward you, alternating the groove for the left and right side grinding. One stretch should take 3 or more seconds depending on the length of the blade.
  • Page 14: Cleaning And Maintenance

    Cleaning and maintenance • Before each cleaning, disconnect the appliance from the mains and allow it to cool down. • Use only a slightly moistened cloth to clean the device itself. • Do not use any solvent or abrasive cleaner. •...

Table of Contents