Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.
Стр. 1 из 1 LEAD-FREE SOLDER This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product. WARNING: This product is manufactured using lead free solder.
Through WEB, ver. 6.5 has been released but with it, the linking function in this manual may not work properly. If ver. 6.5 has been installed, uninstall it and reinstall ver. 6.0. To get ver. 6.0, click the icon, or contact to the nearest Toshiba Service Centre for further assistance. Freezing windows opened (Cannot close the open windows) This may happen occasionally.
Page 5
Стр. 2 из 2 Continue to use by operating the windows. Precaution when opening the diagrams While opening the diagrams, the menu in the left frame changes its color to GRAY. This is an indication that the viewer is processing. With this condition, the menu indication color may stick to the GRAY color or Windows may freeze if clicking other menu.
Page 6
Стр. 1 из 4 IMPORTANT NOTICE User Guide Autodesk® DWF™ Viewer is necessary to view drawings and to activate the functions of this system. Please download and install. When Windows XP SP2 is used, pop-up windows are limited by the enhanced security function and this sample may not work.
Page 7
Стр. 2 из 4 Operating Environment : Pentium III or higher recommended Monitor : 1024 x 768 or higher resolution recommended file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.451\37H... 08.05.2015...
Page 8
Стр. 3 из 4 Mouse : A mouse with wheel recommended : Microsoft Windows 2000/XP Browser Microsoft Internet Explorer 6.0 or later Drawing viewer : Autodesk DWF Viewer 6.0 * Use the software following respective license terms and conditions. Note: In case of using this service manual with network connection, allocate its folder to the client PCs as network drive to avoid any possible malfunction.
Page 9
Стр. 4 из 4 Layer Display Changing Function When any of the color buttons on the toolbar is clicked, it can be selected to display desired layer in its color or not to display each layer. This allows you to see the pattern layer only by setting other layers to "non-display".
Page 10
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Toshiba shall not be liable for any damages, losses, expenses or costs, if any, incurred in connection with or as a result of use of any information or data provided herein.
Стр. 1 из 8 ADJUSTMENT Service Mode Entering to Service Mode 1. Press MUTE button twice on Control. ↓ ↓ ↓ ↓ 2. Press MUTE button again and keep in pressing. ↓ ↓ ↓ ↓ Service Mode display 3. While pressing the MUTE button, press MENU button on TV set.
Page 12
Стр. 2 из 8 Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. Selection of the adjustment items CH (on TV or remote control) Change of the data value Volume +/- (on TV or remote control) Adjustment menu mode ON/OFF MENU button (on remote control) Reset the count of operating CALL + CH button on TV (...
Page 13
Стр. 3 из 8 Item Name of adjustment Data R-CUT R CUTOFF G-CUT G CUTOFF B-CUT B CUTOFF R-DRV G DRIVE G-DRV G DRIVE B-DRV B DRIVE *BRTC BRIGHTNESS CENTER *COLC COLOR CENTER *UVTT BASE BAND TINT *CNTX CONTRAST MAX SHRC SHARPNESS CENTER VBIS VBI Setting Closed Caption...
Page 14
Стр. 4 из 8 OPT3 TV SET OPTION 3 MAGC AGC of MTS decoder Volume1 Data Volume25 Data Volume50 Data Volume75 Data V100 Volume100 Data VOLBS Correction Volume at DTV VOLST Correction Volume at Stereo/SAP of ATV EVOL Reduce Volume For Bassboost (Nonuse) VOLX Volume Limiter For Hotel BASX Bass Max Data TREX Treble Max Data...
Page 15
Стр. 5 из 8 VVDD Reduce Volume For Dolby WFCS FOCUS Level WWSP SRS 3D Level WTBH TruBass High Level WTBL TruBass Low Level VOLM Volume coefficient at 1/2 Mute Adjusting the Data Pressing of VOLUME button will change the value of data in the range from 00H to FFH.
Page 16
Стр. 6 из 8 (1) Version information of TV-MICRO : Display 1 byte data. (2) Version information of TV-MICRO EEPROP : Display 1 byte data. (3) Version information of DVD MPU : HL66 not used. (HLV66, 37LX96 USED) (4) Version information of DMD Engine OEM Revision : LCD Model not used. (5) Version information of DMD Engine ASIC Revision : LCD Model not used.
Page 17
Стр. 7 из 8 "NG : MTS" "NG : APRO" "NG : AVSW" LED Indication The yellow, blue and red/green LED lights on the TV (at the bottom center of the TV) indicate the TV's status, as described below: Note: If the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow LED will blink while the TV is booting until the remote control is usable.
Page 18
Стр. 8 из 8 Check the cause that the protecting circuit of the power supply. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.851\37H... 08.05.2015...
Page 19
Стр. 1 из 2 FUNCTION AND OPERATION TV Front and Side Panel Control and Connection file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.881\37H... 08.05.2015...
Page 20
Стр. 2 из 2 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.881\37H... 08.05.2015...
Стр. 1 из 3 FUNCTION AND OPERATION Learning about the Remote Control file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.837\37H... 08.05.2015...
Page 22
Стр. 2 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.837\37H... 08.05.2015...
Page 23
Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.837\37H... 08.05.2015...
Page 24
Стр. 1 из 5 FUNCTION AND OPERATION Programming Channel into the TV's Channel Memory Programming Channel Automatically file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.216\37H... 08.05.2015...
Page 25
Стр. 2 из 5 Manually Adding and Deleting Channel in the Channel Memory file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.216\37H... 08.05.2015...
Page 26
Стр. 3 из 5 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.216\37H... 08.05.2015...
Page 27
Стр. 4 из 5 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.216\37H... 08.05.2015...
Page 28
Стр. 5 из 5 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.216\37H... 08.05.2015...
Handling the LCD Module Стр. 1 из 4 SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 30
Handling the LCD Module Стр. 2 из 4 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 31
Handling the LCD Module Стр. 3 из 4 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 32
Handling the LCD Module Стр. 4 из 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.155\37H... 08.05.2015...
SAFETY INSTRUCTION [LCD] USA Стр. 1 из 3 SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 34
SAFETY INSTRUCTION [LCD] USA Стр. 2 из 3 inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7. Parts mounting and routing dressing of wirings should be the same as that used originally.
SAFETY INSTRUCTION [LCD] USA Стр. 3 из 3 limit constitutes a potential shock hazard and must be corrected immediately. Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Стр. 1 из 2 SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit...
Page 55
Стр. 2 из 2 All capacitors are ceramic 50 V, unless otherwise noted as the following marks. = Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4.
Page 151
Accessory Стр. 1 из 1 Accessory Location Parts No. Description K902 75002040 REMOCON HAND UNIT, CT-90251 Y101 75002982 OWNERS MANUAL, INST REV1 Y102 75002983 OWNERS MANUAL, OPERATING E/F Y109 23945015 BAG, POLYETHYLENE COVER 250X400 Y170 23845800 HOLDER, WIRE, NYLON66 D6.8 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa1.391\37H...
Page 152
Cabinet Стр. 1 из 1 Cabinet Location Parts No. Description A201 75003545 CESE/COVER/LID FRONT BEZEL ASSY, FRONT BEZEL ASSY A315 75002076 PIECE, C COVER ASSY A320 75002342 PIECE, FRONT AV ASSY A340 75001920 PIECE, BUTTON 7 KEY A380 23717240 SCREW, BITTB3X10SZN A401 75003546 CESE/COVER/LID BACK COVER ASSY, BACK COVER ASSY...
Стр. 1 из 2 PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit...
Page 156
Стр. 2 из 2 : Electrolytic : Metal Film : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.114\37H... 09.05.2015...
Page 157
U01A AV (PE0036) Стр. 1 из 8 Loading ... Location Parts No. Description U01A 75002310 PC BOARD ASSY, PE0036A1, AV C401 76092730 CAPACITOR, CERAMIC CHIP, 16V B 0.1UF K C402 76092730 CAPACITOR, CERAMIC CHIP, 16V B 0.1UF K C403 76105181 CAPACITOR, CERAMIC CHIP, 50V CH 180PF J C601 76092730...
Page 158
U01A AV (PE0036) Стр. 2 из 8 C1811 76619102 CAPACITOR, ELECTROLYTIC CHIP, 16V 47UF M C1812 76092616 CAPACITOR, CERAMIC CHIP, 16V B 0.33UF K C1815 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z C1816 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z C1817 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K...
Page 159
U01A AV (PE0036) Стр. 3 из 8 CA46 76092883 CAPACITOR, CERAMIC CHIP, 50V B 0.1UF K CA200 76092883 CAPACITOR, CERAMIC CHIP, 50V B 0.1UF K CA201 76092883 CAPACITOR, CERAMIC CHIP, 50V B 0.1UF K CC01 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K CC02 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K...
Page 160
U01A AV (PE0036) Стр. 4 из 8 CR03 76105470 CAPACITOR, CERAMIC CHIP, 50V CH 47PF J CS01 76092795 CAPACITOR, CERAMIC CHIP, 6.3V B 2.2UF K CS02 76092795 CAPACITOR, CERAMIC CHIP, 6.3V B 2.2UF K CS03 76105221 CAPACITOR, CERAMIC CHIP, 50V CH 220PF J CS04 76105221 CAPACITOR, CERAMIC CHIP, 50V CH 220PF J...
Page 161
U01A AV (PE0036) Стр. 5 из 8 CS108 76092731 CAPACITOR, CERAMIC CHIP, 16V B 1UF K CS109 76092731 CAPACITOR, CERAMIC CHIP, 16V B 1UF K CS110 76619101 CAPACITOR, ELECTROLYTIC CHIP, 16V 22UF M CS111 76666101 CAPACITOR, ELECTROLYTIC, 16V 100UF M CS112 76092542 CAPACITOR, CERAMIC CHIP, 16V B 1UF K...
Page 162
U01A AV (PE0036) Стр. 6 из 8 CV022 76105100 CAPACITOR, CERAMIC CHIP, 50V CH 10PF D CV023 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K CV024 76666101 CAPACITOR, ELECTROLYTIC, 16V 100UF M CV025 76619157 CAPACITOR, ELECTROLYTIC CHIP, 16V 100UF CV026 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K CV027...
Page 165
U01B F-AV (PE0036) Стр. 1 из 1 U01B F-AV (PE0036) Location Parts No. Description U01B 75002311 PC BOARD ASSY, PE0036A2, F-AV CC11 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K CC12 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K CV122 76105101 CAPACITOR, CERAMIC CHIP, 50V CH 100PF J GR605...
Page 166
U01C LED (PE0036) Стр. 1 из 1 U01C LED (PE0036) Location Parts No. Description U01C 75002312 PC BOARD ASSY, PE0036A3, LED CB01 76202221 CAPACITOR, ELECTROLYTIC, 10V 220UF M CB02 76202221 CAPACITOR, ELECTROLYTIC, 10V 220UF M CB03 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z CB04 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z...
Need help?
Do you have a question about the 37HL66 and is the answer not in the manual?
Questions and answers