TABLE OF CONTENTS SERVICE SAFETY PRECAUTIONS ............................ 3 HANDLING THE LCD MODULE ............................5 LOCATION OF CONTROLS ..............................7 LAYOUT OF MAJOR BOARDS ............................9 MECHANICAL DISASSEMBLY ............................10 PACKING DISASSEMBLY ..............................26 WIRING CONNECTION DIAGRAM ........................... 27 CHASSIS AND CABINET REPLACEMENT PARTS LIST ....................31 PC BOARDS BOTTOM VIEW ............................
SERVICE SAFETY PRECAUTIONS • The caution items shown here describe major safety issues and should always be observed. • The meanings of the various indications are as follows. Indicates a hypothetical situation in which service personnel and nearby third parties, or even WARNING end users due to a product defect after the service operation is completed, could possibly be in danger of injury or even death in the event of operational error.
Page 4
WARNING • Always advise users to keep children away. There is danger of injury to children from tools, disassembled products, etc. KEEP CHILDREN AWAY • Always disconnect the power plug before starting work whenever power is not required. Failure to disconnect the power plug before starting work can result in electrical shock. UNPLUG •...
HANDLING THE LCD MODULE Safety Precautions 3. If the panel surface becomes soiled, wipe with cotton or a In the event that the screen is damaged or the liquid crystal soft cloth. If this does not remove the soiling, breathe on (fluid) leaks, do not breathe in or drink this fluid.
Page 6
7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time. 8. Do not store the LCD module below the temperature con- ditions described in the specifications. Failure to do so could result in freezing of the liquid crystal due to cold air or loss of resilience or other damage.
LOCATION OF CONTROLS Remote sensor TV front TheaterLink Power (IR pass through) indicator POMER POMER Push up Push up Left pocket panel Right pocket panel VIDEO-3 IN TV/VIDEO MENU VOLUME CHANNEL POWER S-VIDEO VIDEO L/MONO HEADPHONE AUDIO MENU POWER Headphones jack VIDEO-3 Volume T S...
Page 8
Remote Control POWER turns the TV on and off. SLEEP allows access to the automatic TV shut-off function . LIGHT The first press of the LIGHT button lights the keypad and turns on the Illumination mode. With the Illumination mode on, pressing any other key lights the keypad for 5 seconds (10 seconds if you’re in programming mode).
MECHANICAL DISASSEMBLY R Removing the rear cover Note: Be sure to lay down the main body (by placing its screen downward) for disassembling. • Remove 13 screws (A). • Remove 4 screws (B). – 10 –...
Page 11
R Removing the brackets • Remove 14 screws (C). • Remove 7 screws (D) and 2 screws (E). – 11 –...
Page 12
R Removing the brackets • Remove flexible wire. • Disconnect the 60P connector. 60P connector G-HYPER Module Push – 12 –...
Page 13
R Removing the A-OUT board • Remove 3 screws (F). A-OUT Board – 13 –...
Page 15
R Removing the SIGNAL board • Remove 4 screws (H) on the SIGNAL board. SIGNAL Board – 15 –...
Page 16
R Removing the LED/RMT board & POW SW board • Remove 2 screws (J) on the LED/RMT board. • Remove 4 screws (K) on the POW SW board. LED/RMT Board – 16 –...
Page 17
R Removing the DVI unit & RF SW module • Remove 2 screws (L) to detach the DVI unit. • Remove 3 nuts (M) fixing the RF SW module. DVI Unit RF SW Module – 17 –...
Page 18
R Removing the SWG POWER/DD POWER module & TIF-MA board • Remove 9 screws (O) ON THE SWG POWER module. • Remove 6 screws (P) on the DD POWER module. • Remove 4 screws (Q) on the TIF-MA board. SWG POWER DD POWER TIF-MA Module...
Page 19
R Removing the BACK/AV board • Remove 2 screws (R) fixing the AC cord bushing. • Remove 10 screws (S) on the BACK/AV panel. • Remove 4 screws (T) on the BACK/AV board. BACK/AV Board AC Cord Bushing BACK/IN Panel –...
Page 20
R Removing the FRONT/AV board • Open the FRONT/AV board holder. • Remove 3 screws (U). OPEN FRONT/AV Board – 20 –...
Page 21
R Removing the KEY board • Open the KEY board holder. • Remove 2 screws (V). OPEN KEY Board – 21 –...
Page 22
R Removing the chassis block • Remove 15 screws (W). – 22 –...
Page 23
R Removing the LCD block • Remove 4 screws (X). Shield Case Shield Case LCD Block – 23 –...
Page 24
R Removing the front panel • Remove 4 screws (Z). – 24 –...
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. • The PC board assembly with mark is no longer available after the end of the production. Model : 26HL83 Capacitors ..... CD Ceramic Disk : Plastic Film : Electrolytic Resistors ....
Page 30
Location Location Parts No. Description Parts No. Description C4703 24073082 ELECTROLYTIC, 50V 2.2UF M 3A CS15 24092726 CERAMIC CHIP CK733B 16V 2,200,000PFK C4704 24092753 CERAMIC CHIP, 10V B 0.22UF K CS16 24092726 CERAMIC CHIP CK733B 16V 2,200,000PFK C4705 24073082 ELECTROLYTIC, 50V 2.2UF M 3A CS20 24669478 ELECTROLYTIC, 50V 0.47UF M 3A...
Page 31
Location Location Parts No. Description Parts No. Description CV244 24109103 CERAMIC CHIP, 50V B 0.01UF K R133 24011101 CHIP, METAL FILM, 1/20W 100 OHM J CV245 24092441 CERAMIC CHIP, 16V F 1UF Z R134 24011103 CHIP, METAL FILM, 1/20W 10K OHM J CV246 24092441 CERAMIC CHIP, 16V F 1UF Z R135...
Page 32
Location Location Parts No. Description Parts No. Description R4702 24011272 CHIP, METAL FILM, 1/20W 2.7K OHM J RS02 24011562 CHIP, METAL FILM, 1/20W 5.6K OHM J R4704 24011103 CHIP, METAL FILM, 1/20W 10K OHM J RS03 24011562 CHIP, METAL FILM, 1/20W 5.6K OHM J R4705 24011474 CHIP, METAL FILM, 1/20W 470K OHM J...
Page 33
Location Location Parts No. Description Parts No. Description RS76 24011562 CHIP, METAL FILM, 1/20W 5.6K OHM J RV120 24871750 CHIP, METAL FILM, 1/8W 75 OHM J RS79 24011104 CHIP, METAL FILM, 1/20W 100K OHM J RV121 24871750 CHIP, METAL FILM, 1/8W 75 OHM J RS80 24011104 CHIP, METAL FILM, 1/20W 100K OHM J...
Page 34
Location Location Parts No. Description Parts No. Description RY508 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J LC04 23103828 INDUCTOR, BEAD, TEM2121M RY509 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J LV01 23103159 FILTER, EMI, TEM2028AA, 7.5X6.4X8 RY510 24011152 CHIP, METAL FILM, 1/20W 1.5K OHM J 60MMH 0.5A RY511 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J...
PC-IN BOARD PD1364A-3 BOTTOM (FOIL) SIDE POWER SW BOARD PD1364A-4 BOTTOM (FOIL) SIDE CON G-HYPER BOARD PD1364A-5 BOTTOM (FOIL) SIDE – 45 –...
Page 42
THIS PAGE IS INTENTIONALLY LEFT BLANK. – 46 –...
Page 43
SCHEMATIC DIAGRAM MODEL : 26HL83 WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
SPECIFICATIONS Television System TheaterLink NTSC standard OUTPUT: 3 V(p-p), 10k ohm Dimensions Channel Coverage Width : 32-9/32 inches (820 mm) VHF: 2 through 13 Height : 18-37/64 inches (472 mm) UHF: 14 through 69 Depth : 5-25/64 inches (137 mm) Cable TV: Mid band (A-8 through A-1, A through I) Super band (J through W) Mass (weight)