Summary of Contents for Himax CLT-50AT-RE
- Page 1 CLT-50AT-RE Power Controller TLF series Electric Screwdriver Operation instructions...
- Page 2 一 注意事項 : I. Notice: 1: 使用此變壓器時,請先閱讀本操作手冊,以期正確安全之使用. Please read this operation manual before using the transformer for correct and safe use. 2: 此變壓器應使用於正確之輸入電壓. The transformer shall be used with correct input of voltage. 3: 此變壓器須於通風良好之埸所使用. The transformer shall be used in a place of good ventilation. 4: 請將變壓器安放於乾淨,乾燥之埸所, 並遠離油氣,瓦斯,雜訊與高壓之地點.
- Page 3 二 面板說明 : II. Explanation of panel 1 : 電源開關. Power switch 2 : HI/LOW 轉速電壓開關 , 可改變輸出於電動起子之電壓 30V/20V. HI/LOW rotary speed voltage switch, may change output voltage of the electric driver by 30V/20V. 3 : 電動起子電源線插座 , 請使用原廠提供之連接線. Electric driver power cord socket, please use the connection line provided by the manufacturer. 4 : 信號狀態指示燈...
- Page 4 三 背板說明 : III. Explanation of backboard 1 : 電源線插座. Power cord socket 2 : 保險絲插座 , 2A/110V 或 1A/230V. Fuse jack, 2A/110V or 1A/230V. 3 : 輸出入信號端子 , 可控制電動起子之起動, 停止與螺絲鎖緊之輸出信號. Output/input signal terminal may control start and stop of electric driver, and screw locking output signal. 4 : 輸入市電選擇開關...
- Page 5 四 變壓器信號時序表 : IV. Transformer signal time scale 五 信號描述 : V. Signal description T1: 電源於關閉後最少 2 秒鐘方可打開電源啟動變壓器. Turn on the power and start the transformer at least in 2 seconds after the power is off. T2: 於變壓器啟動後至少 2 秒鐘方可輸入信號以啟動電動起子. Input the signal to start the electric driver at least in 2 seconds after the transformer is started.
- Page 6 T6: 螺絲鎖緊時由變壓器背板 ( Finish ) 輸出之信號, 時間長短之決定為螺絲鎖緊後至 Stop 信號輸入為止. Signal output by the backboard (Finish) of the transformer when the screw is locked, lasting for a period from the time when the screw is locked until the input of Stop signal. T7 : 為停止信號...
- Page 7 七 輸出信號 VII. Output signal Relay of contact rating Rate Load AC110V 0.5A , DC24V1A Max. Allowable Voltage 125VAC , 30VDC Max. Allowable Current 八 規格 : VIII. Specifications Model : CLT - 50AT-RE Size : 180mm * 90mm * 85mm Weight : 2700g Input Voltage : AC 110V or 230V 50/60Hz AC Plug Cord Length : 1.8m...
- Page 8 <操作说明> Operation instructions 1. This unit can be used to count the quantity of finished products and number of screws to be locked in a single product. 2. Make sure the input power and input signal are correct before use. 3.
Need help?
Do you have a question about the CLT-50AT-RE and is the answer not in the manual?
Questions and answers