Advertisement
Quick Links
To learn more about BIESEMEYER MANUFACTURING
visit our web site at: www.biesemeyer.com.
For Parts, Service, Warranty or other assistance,
1-800-782-1831
please call
B
IESEMEYER
Commercial Fence System
® T-S
®
QUARE
(Model BC30)
(Model BC30W)
(Model BC50)
(Model BC50W)
PART NO. 1352432
REVISED 03-01-07
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Biesemeyer T-SQUARE BC30
Summary of Contents for Biesemeyer T-SQUARE BC30
- Page 1 IESEMEYER QUARE Commercial Fence System (Model BC30) (Model BC30W) (Model BC50) (Model BC50W) PART NO. 1352432 REVISED 03-01-07 To learn more about BIESEMEYER MANUFACTURING visit our web site at: www.biesemeyer.com. For Parts, Service, Warranty or other assistance, 1-800-782-1831 please call...
- Page 2 INTRODUCTION The B ® ® Commercial fence system includes the fence assembly, front rail, rear rail IESEMEYER QUARE and front guide tube along with the mounting hardware for assembling the fence system to many different types of table saws. Depending on the model ordered, an accessory leg kit may also be included.
- Page 3 18 19 20 21 22 23 24 29 30 Fig. 2 ® 1. T-Square Fence For Attaching Extension Table (All Saws) 2. Support Leg (2) 18. 1/4-20 x 1-1/2” Flat HD Screw (14) 3. Leveling Foot (2) 19. Fender Washer (14) 4.
- Page 4 CONSTRUCTING EXTENSION TABLE Fig. 4 ASSEMBLY (DELTA SAWS ONLY) FOR ALL OTHER SAWS, PROCEED DIRECTLY TO PAGE 7, STEP 1. DISCONNECT THE SAW FROM THE POWER SOURCE! FRONT RAIL TO SAW 1. Assemble front rail (A) Fig. 5 to the front edge of the saw table using the two 5/16-18 x 1-1/4”...
- Page 5 REAR RAIL FOR DELTA SAWS NOTE: Do not use template to set rear rail. 3. Align the two non-countersunk holes in the rear rail with the two holes in the rear edge of the saw table. The two cutouts in the rear rail need to be below the bottom of the two miter slots in the saw table.
- Page 6 6. Lay the table upside down on the floor or on a bench. 7. Position the table leg (I) to the closed in corner of the extension table (J) as shown in Fig. 11. 8. Attach the table leg to the table board with six 5/8” long wood screws (K).
- Page 7 ASSEMBLY (FOR ALL OTHER SAWS) DISCONNECT THE SAW FROM THE POWER SOURCE! ASSEMBLE FRONT RAIL 1. Raise saw blade (A) Fig. 15. Place a straight edge (B) against the right side of saw blade extending out over the front of the saw as shown. Position front rail (C) against the edge of saw table and lightly clamp in place using bar clamps (D).
- Page 8 IMPORTANT: If your saw fence system will be used with a mobile base underneath the saw base and table legs, the position of the legs will have to be changed to fit the mobile base extension. 9. Lay the extension table upside down on a floor or bench. 10.
- Page 9 ASSEMBLY (FOR ALL SAWS) 1. Attach knob (A) Fig. 23 to locking handle (B). Knob is screwed onto threads of locking handle. 2. Align fence side (C) Fig. 24, with the miter slot on the table saw and lock fence in position. Using a measuring tape (D), measure the distance from the saw blade to the Fig.
- Page 10 Fig. 27 5. When the fence locking handle (B) Fig. 28, is pushed to the down position, the fence assembly (C) should be completely clamped to the guide tube. If the fence assembly (C) is not completely clamped to the guide tube when the handle is pushed down, as shown, lift up handle (B) and raise fence off the guide tube as shown in Fig.
- Page 11 9. The distance the fence is positioned away from the saw blade is indicated by the witness line (S) located in cursor (E), Fig. 31. To calibrate the cursor to the saw blade, make a test cut with the fence locked in position. Measure the width of the cut piece.
- Page 12 TWO YEAR LIMITED NEW PRODUCT WARRANTY Delta will repair or replace, at its expense and at its option, any new Delta machine,machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.
Need help?
Do you have a question about the T-SQUARE BC30 and is the answer not in the manual?
Questions and answers