ST LRI DemoKit V3.0 User Manual

Long range contactless memory demokit reader

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

UM0073

USER MANUAL

ISO15693 Long Range Contactless Memory

DemoKit (V3.0) Reader

This document describes the hardware and software of the STMicroelectronics LRI DemoKit V3.0 (Order-

ing code: DemoKitLR) working under the Windows 95/98/NT/2000 operating systems.

Figure 1. LRI DemoKit V3.0

July 2004

1/15

Table of Contents

Need help?

Do you have a question about the LRI DemoKit V3.0 and is the answer not in the manual?

Questions and answers

Summary of Contents for ST LRI DemoKit V3.0

Page 1 USER MANUAL ISO15693 Long Range Contactless Memory DemoKit (V3.0) Reader This document describes the hardware and software of the STMicroelectronics LRI DemoKit V3.0 (Order- ing code: DemoKitLR) working under the Windows 95/98/NT/2000 operating systems. Figure 1. LRI DemoKit V3.0 July 2004...
Page 2: Table Of Contents
Launching the LRI DemoKit V3.0 Software ........
Page 3 ISO15693. This mechanism is supported by the LRI DemoKit V3.0 reader and pro- gram. The LRI DemoKit V3.0 gives access to the full memory mapping. It is possible to read and write into the selected LRI memory. This release of the demonstration software allows the block write protection of the LRI512 to be activated.
Page 4: Hardware Configuration
UM0073 - USER MANUAL HARDWARE CONFIGURATION The hardware is simple to set up: 1. Connect the antenna to the reader board (see Figure 2.). 2. Connect the reader board to the Serial Port A (COM1) or Port B (COM2) of the PC. 3.
Page 5: Reader Firmware Upgrade
UM0073 - USER MANUAL READER FIRMWARE UPGRADE The FEIG MR100 reader firmware needs, first, to be upgraded, for it to work with LRI64 contactless mem- ory devices. To download the “ABDG30100-mr100-a.mhx” firmware code into the MR100 reader flash memory, follow the steps described in the “N10301-0e-ID-A.pdf” guide. When this new firmware is correct- ly installed, follow the actions listed, below, to install all the new software tools: 1.
Page 6: Software Installation
UM0073 - USER MANUAL SOFTWARE INSTALLATION The kit contains one program, “LRI DemoKit V3.0.exe”, on the CD-ROM. It needs a standard PC with a serial port, and: a Windows 95/98 operating system, or Windows NT4.0/2000 (or later). (This is true 32-bit software, and hence will not run on Windows 3.11)
Page 7: Demonstration Program
Figure 5. "Search ReaderParameters" Window Click on “OK” to start the LRI DemoKit V3.0 program. If the search engine stays in the search loop for a long time, click on “CANCEL”, and check that the reader is correctly powered, and that the serial cable is correctly connected.
Page 8: User Interface
UM0073 - USER MANUAL Figure 7. LRI DemoKit V3.0 Screen USER INTERFACE The LRI DemoKit V3.0 screen is divided in three panels. Click on a tab to show the appropriate one. – Read Tags : This panel shows all the LRI tags that are present in the electromagnetic field of the reader. The memory content of each tag can be individually accessed.
Page 9: Assigning Images To Tags
UM0073 - USER MANUAL ASSIGNING IMAGES TO TAGS First, select the “Assign Tags” panel. Click on the “Start” button and place some LRI memory tags in the field of the reader. The screen will appear roughly as shown the Figure Figure 8.
Page 10: Reading Tags
UM0073 - USER MANUAL READING TAGS Select the “Read Tags” panel. Click on the “Start” Button, and put some LRI memory tags in the field of the reader. The screen will appear roughly as shown in Figure Figure 9. "Read Tags" Panel In this panel you can see the inventoried tags with their memory types, and their corresponding images.
Page 11 UM0073 - USER MANUAL You can click on one of the LRI512 tag icons to access its memory. A dialog box, as shown in Figure 10., appears. The content of LRI64 memory tags can be accessed only in the SuperUser panel. Figure 10.
Page 12: Superuser Mode
UM0073 - USER MANUAL SUPERUSER MODE Select the “SuperUser” panel. The screen will appear roughly as shown in Figure 11.: Figure 11. "SuperUser" Panel Inventory To start the inventory, click on the “Inventory” button. All the tag UIDs that are found during this sequence are displayed as a UID tag list, together with the memory type in parentheses, in the text box “Serial Num- ber”.
Page 13: Persistence Control
To select an image set in another directory, you have to click on “No” in the “Choose folder window” when you start the LRI DemoKit V3.0 program. A file popup window will appear. Then, select the new image set directory.
Page 14: Revision History
UM0073 - USER MANUAL REVISION HISTORY Table 1. Document Revision History Date Version Revision Details 25-Feb-2004 First Issue, describing v2.0 of the demonstration program 12-Jul-2004 Document revised to describe v3.0 of the demonstration program 14/15...
Page 15 This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

This manual is also suitable for:

Demokitlr