Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PCB Piezotronics Vibration Division 682A09
Summary of Contents for PCB Piezotronics Vibration Division 682A09
- Page 1 Model 682A09 MANUAL (682A09) Installation and Operating Manual For assistance with the operation of this product, contact the Vibration Division of PCB Piezotronics, Inc. Division toll-free: 888-684-0013 24-hour SensorLine: 716-684-0001 Fax: 716-685-3886 E-mail: vibration@pcb.com...
- Page 2 Returning Equipment – Following the equipment to PCB Piezotronics for these procedures will insure that your repair. User servicing or repair is not returned materials are handled in the recommended and, if attempted, may most expedient manner.
- Page 3 PCB Piezotronics, Inc. Warranty – All equipment and repair 3425 Walden Ave. services provided by PCB Piezotronics, Depew, NY 14043 USA Inc. are covered by a limited warranty Toll-free: (800) 828-8840 against defective...
- Page 4 Model 682A09 Industrial in line ICP to 4 to 20 mA converter Installation and Operating Manual For assistance with the operation of this product, contact the IMI-Sensors Division of PCB Piezotronics, Inc. Division toll-free: 24-hour SensorLine: Fax: 716-684-3823 E-mail: imi@pcb.com...
- Page 5 Returning Equipment - Following these procedures will insure that your the equipment to PCB Piezotronics for repair. User servicing or repair is not returned materials are handled in the recommended and, if attempted, may most expedient manner.
- Page 6 PCB Piezotronics, Inc. Warranty - All equipment and repair 3425 Walden Ave. services provided by PCB Piezotronics, Depew, NY 14043 USA Inc. are covered by a limited warranty Toll-free: (800) 828-8840 against defective...
- Page 7 Operating Guide with Enclosed Warranty Information 3425 Walden Avenue, Depew, New York 14043-2495 Phone (716) 684-0003 Fax (716) 684-3823 Toll Free Line 1-800-959-41 Ml...
-
Page 8: Table Of Contents
A PCB PIEZOTRONICS DIV. Table of Contents Introduction ........................Page 3 General Features Dimension Drawing ......................Page 4 Operation and Wiring.......................Page 5 Standard Wiring Taking Measurements RV Option RVVO Option TO Option Installation........................Page 7 Direct Adhesive Mount Standard Stud Mount Adhesive Stud Mount Magnetic Mount ESD Sensitivity.......................Page 11... -
Page 9: Introduction
A PCB PIEZOTRONICS DIV. Introduction The Model 682A09 Series Industrial in line ICP to 4-20mA converter transfers the signal from any 100 mV/g ICP industrial accelerometer to 4-20mA overall vibration velocity. The converter outputs a 4-20mA signal that is proportional to the overall velocity and raw acceleration of the machinery. Ideal for monitoring the vibration of process equipment such as fans, motors and pumps, the output of the converter is routed to a PLC, DCS or SCADA system and used for process control or predictive maintenance. -
Page 10: Dimension Drawing
A PCB PIEZOTRONICS DIV. Dimension Drawing Page 4... -
Page 11: Operation And Wiring
A PCB PIEZOTRONICS DIV. Operation and Wiring Standard Wiring The Model 682A09 Series operates from a standard 2-wire, 4-20mA loop. If using a loop power, attach at 3- Pin connector side the positive (+) input from the power supply to Pin A and the negative (-) input from the power supply to Pin B. - Page 12 A PCB PIEZOTRONICS DIV. RV Output The RV (raw vibration) output is a pass-through for the 100 mV/g industrial accelerometer connected to the model 682A09. The frequency range and accuracy of the signal will be dependant upon the accelerometer used.
-
Page 13: Installation
A PCB PIEZOTRONICS DIV. Accelerometer Installation When choosing a sensor mounting method, consider closely the advantages and disadvantages of each technique. Typical mounting types are stud, direct adhesive, adhesive mounting base and magnetic mounting base. Since the frequency response at velocity is limited to 1 kHz on the 682A09, any of the four methods can be used without seriously affecting this data values. -
Page 14: Standard Stud Mount
A PCB PIEZOTRONICS DIV. Standard Stud Mount Procedure This mounting technique requires smooth, flat contact surfaces for proper operation and is recommended for permanent and/or secure installations. Stud mounting is also recommended when testing at high frequencies. Note: DO NOT attempt mounting on curved, rough or uneven surfaces, as the potential for misalignment and limited contact surface may significantly reduce the sensor's upper operating frequency range. -
Page 15: Adhesive Stud Mount
A PCB PIEZOTRONICS DIV. Adhesive Stud Mount Procedure Adhesive mounting is often used for temporary installation or when the machine surface cannot be adequately prepared for stud mounting. Adhesives like hot glue or wax work well for temporary mounts; two-part epoxies and quick-bonding gels provide a more permanent mount. -
Page 16: Magnetic Mount
A PCB PIEZOTRONICS DIV. Magnetic Mount Procedure Magnetic mounting provides a convenient means for making portable measurements and is commonly used for machinery monitoring and other portable or trending applications. Note: The correct magnet choice and an adequately prepared mounting surface are critical for obtaining reliable measurements, especially at high frequencies. -
Page 17: Esd Sensitivity
Warning 2 - ESD sensitivity This equipment is designed with user safety in mind; however, the protection provided by the equipment may be impaired if the equipment is used in a manner not specified by PCB Piezotronics, Inc. Page 11...