Related Manuals for InCarTec CAR-INTERFACE CI-V5-CIC-E-PNP
Summary of Contents for InCarTec CAR-INTERFACE CI-V5-CIC-E-PNP
- Page 1 v.LOGiC Intelligent Solution Interface CI-V5-CIC-E-PNP Compatible with the E-series BMW and Mini with navigation system or radio and 6.5” or 8.8” monitor with 4pin HSD LVDS connector Version 11.01.2018 CI-V5-CIC-E-PNP...
- Page 2 Product features Own on-screen display and setup Rear-view camera input Automatic switching to rear-view camera input on engagement of reverse gear from all operation modes Front camera input Manual switching to rear-view camera (only for vehicles with PDC button) ...
-
Page 3: Table Of Contents
Contents 1. Prior to Installation 1.1. Delivery contents 1.2. Check compatibility of vehicle and accessories 1.3. Setting the dip switches of the interface-box V5C-M636 1.4. LED’s of the interface-box V5C-M636 2. Connection schema 3. Installation 3.1. Connecting interface-box and harnesses 3.2. - Page 4 Legal Information By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
-
Page 5: Prior To Installation
1. Prior to installation Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents Take down the SW-version and HW-version of the interface boxes, and store this manual for support purposes. -
Page 6: Setting The Dip Switches Of The Interface-Box V5C-M636
1.2. Setting the dip switches of the interface-box V5C-M636 Dip 1 and 2 on the back of the interface-box V5C-M636 are used to set the monitor type. The default setting is: Vehicle/ navigation Dip 1 Dip 2 Dip 3 CIC-E (E-series), 6.5“ monitor – version 1 CIC-E (E-series), 6.5“... -
Page 7: Connection Schema
2. Connection schema Version 11.01.2018 CI-V5-CIC-E-PNP... -
Page 8: Installation
3. Installation Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent 12V source. If according to factory rules disconnecting the battery is to be avoided, it is usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead. -
Page 9: Lvds Connection
Connect female 8 pin molex connector of the harness TV-BM01 to the male 8 pin molex connector of the harness TV-BM01. Connect female 12pin AMP connector of the harness TV-BM01 to the front site of the V5C-M636 interface box. 3.2. LVDS connection Interface-box V5C-M636... -
Page 10: After-Market Front Camera
3.2.1. After-market front camera 3.2.1.1. Connection to the after-market front camera Interface-box V5C-M636 FRONT V5C-UNI01 harness Front camera +12V camera Power Out 1 (max. 1A) power Connect the video RCA of the after-market front camera to the female RCA connector “FRONT CAM”... -
Page 11: Settings For Connecting An After-Market Front Camera
3.2.1.2. Settings for connecting an after-market front camera You have to configure some settings in the OSD- menus INPUTS and MISC if you want to connect an after-market front camera (Operation of the OSD: see chapter “OSD- Operation”). OSD-menu Menu item Setting Explication No front camera connected... -
Page 12: After-Market Rear-View Camera
3.2.2. After-market rear-view camera 3.2.2.1. Connection to the after-market rear-view camera Connect the video RCA of the after-market rear- view camera to the female RCA connector “REAR CAM” of the interface box V5C-M636. The green wire of harness TV-BM01 can be used for +12V electric power supply (max. -
Page 13: Settings For Connecting An After-Market Rear-View Camera
3.2.2.2. Settings for connecting an after-market rear-view camera You have to configure some settings in the OSD-menus INPUTS and MISC if you want to connect an after- market rear-view camera (Operation of the OSD: see chapter “OSD-Operation”). OSD-menu Menu item Setting Explication No rear-view camera connected... -
Page 14: Configurable Trigger Outputs
3.2.3. Configurable trigger outputs You can configure the both +12V trigger outputs separately. The pink wire is POWER OUT 1 and the green wire is POWER OUT 2. Note: You can configure the both trigger outputs in the OSD-menu MISC separately (Operation of the OSD: see chapter “OSD- Operation”). -
Page 15: Picture Settings
3.3. Picture settings You can change the picture settings in the OSD-menu IMAGE (Operation of the OSD: see chapter “OSD-Operation”). ◦ Brightness ◦ Contrast ◦ Saturation ◦ Hue ◦ Sharpness Note: The picture settings will be retained for each AV-source separately. Version 11.01.2018 CI-V5-CIC-E-PNP... -
Page 16: Operation
4. Operation 4.1. OSD – On-screen display You can change the basic configurations of the interface in the OSD (on screen display). 4.1.1. OSD – Operation You can control the OSD by iDrive. 4.1.1.1. 8-button iDrive Version 11.01.2018 CI-V5-CIC-E-PNP... -
Page 17: 2-Button Idrive In Mini
4.1.1.2. 2-button iDrive in Mini 4.1.2. OSD – Additional setting options The following settings in the OSD-menus OSD and MISC can be configured over and above the described settings in this manual (Operation of the OSD: see chapter “OSD-Operation”): OSD-menu Menu item Setting Explication... -
Page 18: Video-In-Motion Function
4.2. Video-in-motion function It is possible to activate and deactivate the video-in-motion in the OSD menu “MISC” (Operation of the OSD: see chapter “OSD-Operation”). OSD-menu Menu item Setting Explication Video-in-motion activated MISC Video-in-motion deactivated For the V5-CIC-E-PNP the video-in-motion function is permanently active without disturbing the navigation performance. -
Page 19: Specifications
5. Specifications Operation voltage 10.5 – 14.8V DC Stand-by power drain <0,1mA Operation power drain 190mA Power consumption 2,6W Temperature range -20°C to +80°C Weight (box only) 285g Measurements (box only) B x H x T 141 x 30 x 105 mm 6.