Download Print this page

Porter 2400 Series Assembly & Operation Manual

Floor cover transport/storage systems

Advertisement

Quick Links

A
& O
M
SSEMBLY
PERATION
ANUAL
F
C
T
/S
S
LOOR
OVER
RANSPORT
TORAGE
YSTEMS
No. 2400 Series
Proceed to Page 2 for Assembly Instructions
Proceed to Page 11 for General Operating Instructions
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE,
AND TO ORDER REPLACEMENT PARTS
INST 00353 071
 2001 PORTER ATHLETIC EQUIPMENT COMPANY. ALL RIGHTS RESERVED.
7-1-2001

Advertisement

loading
Need help?

Need help?

Do you have a question about the 2400 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Porter 2400 Series

  • Page 1 No. 2400 Series Proceed to Page 2 for Assembly Instructions Proceed to Page 11 for General Operating Instructions SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE, AND TO ORDER REPLACEMENT PARTS INST 00353 071  2001 PORTER ATHLETIC EQUIPMENT COMPANY. ALL RIGHTS RESERVED. 7-1-2001...
  • Page 2 WARNING READ ALL INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING TO ASSEMBLE THIS EQUIPMENT. ASSEMBLY OF THIS EQUIPMENT MUST BE DONE ONLY BY ADULTS, WHO ARE PHYSICALLY CAPABLE OF DOING SO. THREE (3) ADULTS WILL BE REQUIRED FOR THE ASSEMBLY PROCESS. FOUR (4) ADULTS WILL BE REQUIRED EACH TIME A VINYL SECTION IS INSTALLED ON A BATTEN TUBE.
  • Page 3 1. Check all items against Parts List on Page 2 to ensure all have been included. ASSEMBLY OF TRANSPORT CART 2. Locate two end frame weldments (1), and Detail "A" assemble swivel casters (9 & 10) to each one. Note that each end frame will require one swivel caster with brake (10), and one swivel caster without brake (9).
  • Page 4 3. Complete assembly of transport cart by assembling spreaders and braces to end frames from Step No. 2. NOTE – This will require three physically capable adults – one to hold each the end frame in a vertical position, one to maneuver the spreaders and braces into place, and one to secure the hardware.
  • Page 5 ASSEMBLY OF ROLLER PLATES AND BATTEN TUBE ASSEMBLIES TO THE TRANSPORT CART 9. Determine the quantity of batten tube assemblies to be installed on your system. This quantity will dictate the location and spacing of the roller supports for the batten tubes. See Detail "C" for locations and spacing. Hint – An easy, consistent way to locate the roller assemblies is to measure from the end frame to the small hole for the self-drilling screw.
  • Page 6 10. The roller supports for each batten tube must be installed identically on both end frames, to ensure the batten tube is level and rolls properly. This will also ensure that each vinyl section rolls onto the batten tube straight and even. 11.
  • Page 7 14. At the roller assemblies with the batten tube stop, snug the machine screw and locking cap nut that the batten tube stop pivots on. Do not over-tighten – the stop (19) must be allowed to pivot freely. 15. After all roller support assemblies are properly located and securely mounted to the end frames, install the #12 x 7/8" lg. self- drilling screws (27).
  • Page 8 18. Clean an area on the floor that is large enough to accommodate one section of vinyl for the floor cover. Carefully open a section of vinyl and completely unfold it on the floor. At one end, you will find the Velcro strips for securing the vinyl to the batten tube assembly.
  • Page 9: Optional Accessories

    OPTIONAL ACCESSORIES  No. 02405-000 Power Winder – Use in place of hand crank assemblies. Allows for effortless rolling and unrolling of vinyl sections onto transport/storage cart. Plugs into standard 110-volt outlet.  No. 02406-200 (Hand-Held) and No. 02406-300 (Walk-Type) Tape Applicators.
  • Page 10 WARNING READ ALL WARNINGS THOROUGHLY BEFORE USING THIS EQUIPMENT. FAILURE TO COMPLY WITH THE FOLLOWING INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS INJURIES AND/OR PROPERTY DAMAGE. • Never leave the crank assemblies (or optional No. 02405-000 Power Winder) unattended on the transport/storage cart. Always keep them stored in a secure location, to prevent usage by unauthorized individuals.
  • Page 11 4. Repeat Step No. 3 for each additional vinyl section. Allow approximately 1" overlap as each vinyl section is laid next to the previous one. 5. It is highly recommended that adjacent vinyl sections be secured to each other with tape. Use Porter's No. 02406-112 3" Wide Clear Tape to join vinyl sections together.
  • Page 12 This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Porter Athletic Equipment Company 2500 South 25 Avenue, Broadview, IL U.S.A., 60155 Toll Free: (800) 947-6783 • Phone: (708) 338-2000 • Fax: (708) 338-2060 www.porter-ath.com...