Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for REDHEAD RH360
- Page 1 Elec- tronic Dog Trainer...
- Page 2 NOTICE! According to how you use your transmitter, the transmitting range might be much different. You will have more range if you use your transmitter apart from your body as follows: Maximum Range Typical Range Minimum Range...
-
Page 3: Table Of Contents
TABLE OF CONTENTS • Table of Contents ........3 • Introduction ..........4 • Package Contents ........5 • Model Features ........... 5 • Parts and Functions ........6 • Installing/Charging Batteries ....... 10 • Turning ON and OFF ........11 •... -
Page 4: Introduction
INTRODUCTION Congratulations and thank you for purchasing our RedHead RH360 Remote Dog Trainer. RH360 Dog Training Collar is durable, safe and very humane when used correctly. This training system offers Maxx-Range™ technology, the industry’s only internally woven antenna in the collar. -
Page 5: Package Contents
IMPORTANT NOTE: Please read this owner’s manual in its entirety before operating this unit. Should you have any questions about our collars or their operation please contact our Customer Service department (see back page for address and phone number information). PACKAGE CONTENTS •... -
Page 6: Parts And Functions
PARTS & FUNCTIONS Antenna Indicator Intensity Light Selection Dial Beep Continuous Button Stimulation Button Battery Compartment Magnet (in back) Indicator (Red Mark in back) Lanyard Attachment Transmitter... - Page 7 PARTS & FUNCTIONS Intensity Selection Dial The intensity selection dial allows you to choose between 15 different levels of stimulation for very precise control. On the ‘M’ setting, you can choose between regular and Battery Saving Mode* (see page 12). Transmitter Antenna Be sure to check that the antenna is securely fastened to the transmitter before each use.
- Page 8 PARTS & FUNCTIONS Collar Belt with Embedded Receiver Buckle with Antenna Activation Contacts Magnet Indicator Light Speaker Magnetic Switch Indicator (“M” Mark) Collar Receiver Collar SmartLED Indicator Light When the collar unit is on, the SmartLED will flash green at 51%-100% charge, and will flash red if it has 21%-50% charge.
- Page 9 PARTS & FUNCTIONS Magnetic Switch Indicator (“M” Mark) The Magnetic Switch Indicator is an “M” showing where the Magnetic Activation Switch is located. You can use the Magnetic Indicator on the Transmitter or the Activation Magnet on the Buckle to activate and deactivate your Collar Receiver (see page 11).
-
Page 10: Installing/Charging Batteries
INSTALLING/CHARGING BATTERIES Transmitter Battery 1. Open Battery back Transmitter. 2. Install new 9V battery with ‘-’ terminal on left and ‘+’ terminal on right. 3. Slide the Battery Compartment cover back into place until it clicks. Collar Battery Charging Procedure 1. -
Page 11: Turning On And Off
TURNING THE UNIT ON AND OFF NOTE The Transmitter is always in a permanent sleep state. It is only ON when a button is being pressed, and it does not need to be turned OFF by the user. Turning the Collar Receiver ON 1. -
Page 12: Battery Saving Mode
BATTERY SAVING MODE The Battery Saving Mode will reduce battery consumption in the Collar Receiver and increase battery life. In the Battery Saving Mode, the Collar Receiver battery can last up to approximately 30% longer.* *These figures are estimates and vary depending on numerous factors such as number and length of beeps/stimulations, intensity level setting, distance, weather, storage, battery brand and age, etc. -
Page 13: Testing
TESTING NOTE: Turn the Collar Receiver ON for Testing To Test the Electronic Stimulation: 1. Place the tester firmly on the contacts of the Collar Receiver. 2. Set the intensity (note - an intensity level setting of 4 or less might not be enough to light the tester). -
Page 14: Reprogramming
REPROGRAMMING If your current Collar Receiver is not responding to the Transmitter, it may need to be reprogrammed to the Transmitter. 1. Hold the Magnet Indicator (Red Mark) on the Transmitter directly against the Magnetic Switch Indicator (“M” Mark) on the side of the Collar Receiver. 2. -
Page 15: Properly Fitting The Collar
PROPERLY FITTING THE COLLAR NOTE: Proper collar tightness and position are very important to ensure safe and consistent collar use. All electronic collars need to be very snug around the dog’s neck to work properly. They must be just tight enough to allow the “contacts”... -
Page 16: Setting The Intensity Level
SETTING THE INTENSITY LEVEL It is very important to set the correct intensity level on RH360 your System before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. 1. Place the Intensity Selection dial so that the system is set on Level 1. -
Page 17: Maintenance
MAINTENANCE RH360 It is very important to periodically clean your system for maximum performance. Regular cleaning will also lengthen the life of your unit. RH360 • Clean the collar box with lukewarm water and a mild anti-bacterial soap. • Take care to thoroughly clean the space between the Contacts and the Collar Belt. -
Page 18: Important Safety Notes
Never leave your dog unattended with the unit on. Since no electronic device is perfect, there is a very slight possibility that your dog may receive an unintentional electric stimulation. RH360 • Your training collar is a very valuable tool if used correctly. -
Page 19: Warranty
All RH360 systems have a one year parts and labor warranty effective from the original date of purchase. A copy of the original sales receipt is required to validate the date of purchase. The RH360 has been made with State of the Art equipment. Any fine adjustment should be performed only by DT Systems technicians. -
Page 20: Contact Information
DT Systems 2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dtsystems.com E-mail: customerservice@dtsystems.com...
Need help?
Do you have a question about the RH360 and is the answer not in the manual?
Questions and answers