Table of Contents
Summary of Contents for Mega BEAM 200
- Page 1 MEGA BEAM200 MOVING HEAD LIGHT MJ-1016 User manual Thank you for choosing our beam moving head light. For the sake of your safety, Please read and follow these instructions carefully and keep this manual in a safe place for future...
-
Page 2: Table Of Contents
Catalogue Chapter Page Safe Usage Of The Product ------------------------------------------------------------------------------------------3 Install The Equipment -------------------------------------------------------------------------------------------------4 Fitting The Lamp --------------------------------------------------------------------------------------------------------4 Power Code Connection ----------------------------------------------------------------------------------------------5 DMX Connection -------------------------------------------------------------------------------------------------------5 DMX Terminator --------------------------------------------------------------------------------------------------------6 Function Set ---------------------------------------------------------------------------------------------------------------6 Operation Menu ----------------------------------------------------------------------------------------------------------7 Maintenance ---------------------------------------------------------------------------------------------------------------9 Keeping The Product Clean -------------------------------------------------------------------------------------------9 Trouble Shooting ----------------------------------------------------------------------------------------------------------9 Equipment and Appendix... -
Page 3: Safe Usage Of The Product
SAFE USAGE OF THE PRODUCT When unpacking and before disposing of the carton, check there is no transportation damage before using the product. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The product is for indoor use only, IP20. -
Page 4: Install The Equipment
Install The Equipment: Use 2pcs clamp and 1safety cord(need to purchase).Use clamp fix with light hook which in the packing box with light, then use screw install to the bottom of lamp. Hang the fixture on the structure and fasten the screws attached to each clamp. Make sure the light is installed reliable, and confirm the light which you fixed is strong enough for hanging the light. -
Page 5: Power Code Connection
Power Code Connection: Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off. -
Page 6: Dmx Terminator
DMX Terminator: In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. -
Page 7: Operation Menu
Reel Opertion Use reel can set the address code and function code easily. Check or modify lighting function settings, rotation the REEL. LCD display panel will display main menus. Function operation menu all have corresponding submenu . Each menu all represent the specific functions of lamps, specific see below "operation menu"... - Page 8 Test operation Program run Sound Auto Program run Lamp set up ON/OFF Lamp switch Starting state ON/OFF Resume default Enter Enter Fixture reset Ver.4.1 Version 1) Address settings DMX address settings:001-255 2) Control mode 3) Option mode ◆ X-axis inversion Off --X-axis forward work(default setting) ON--X-axis inverse work ◆...
-
Page 9: Maintenance
Maintenance: To prolong the life of the projector, some maintenance work has to be done to ensure the optical system in good condition. If the projector does not function, check the fuses on the power socket of the projector, they should only be replaced by fuses of the same specification. Should these be damaged, call a qualified technician before replacement. -
Page 10: Equipment And Appendix
Equipment and Appendix: ☆ Beam 200W Moving Head Light 1pcs ☆ Power Cable 1pcs ☆ XLR connector 1unit ☆ Light Hook 2pcs ☆ The Product of Instruction 1pcs Channel List: (16CH MODE) Channel Value Function White 4~11 Color1 12~19 Color 2 20~27 Color 3 28~35... - Page 11 White 7~13 Gobo 1 14~20 Gobo 2 21~27 Gobo 3 28~34 Gobo 4 35~41 Gobo 5 42~48 Gobo 6 49~55 Gobo 7 56~62 Gobo 8 63~69 Gobo 9 70~76 Gobo 10 (Gobo) 77~83 Gobo 11 84~90 Gobo 12 91~97 Gobo 13 98~104 Gobo 14 105~111...
-
Page 12: Technical Parameters
Technical Parameters: Voltage : 100~240V/50-60Hz Power consumption:350W@(220V) Bulb: HAOYE HYSL5R200 200W projection lamp Lamp : HAOYE HYSL7R200W Color temperature : 8500K Color: 14 color + blank color wheel Gobo: 17 fixed gobo + blank gobo Prism : 1 rotation 16-face prism, Bilateral rotation .frost function Dimmer : 0-100% linear adjustment ,Strobe(0.5-9 times/ second) Beam angle : parallel beam angel 0 –...
Need help?
Do you have a question about the BEAM 200 and is the answer not in the manual?
Questions and answers