Table of Contents
Advertisement
Quick Links
MODEL 55-0045
MOTOR LIFT
INSTALLATION
AND
OPERATING INSTRUCTION
For outboards up to 35HP weighing up to 263 pounds.
This motor lift is designed for clamp screw type outboards only.
651.486.2010
MARINETECH PRODUCTS, INC
1360 East County Road E
VADNAIS HEIGHTS, MN 55110
www.marinetechproducts.com
REV 12/15
99-55288
1
1.604.940.2010 | sales@cmpgroup.net
Advertisement
Table of Contents
Summary of Contents for CMP Panther 55-0045
- Page 1 MODEL 55-0045 MOTOR LIFT INSTALLATION OPERATING INSTRUCTION For outboards up to 35HP weighing up to 263 pounds. This motor lift is designed for clamp screw type outboards only. 651.486.2010 MARINETECH PRODUCTS, INC 1360 East County Road E VADNAIS HEIGHTS, MN 55110 www.marinetechproducts.com REV 12/15 99-55288...
- Page 2 INTRODUCTION Congratulations, you have just purchased one of the finest auxiliary outboard motor lifts available today. With proper installation and care, this motor lift will provide you with years of trouble free use and performance. Please take a few moments to review the information contained in this booklet to familiarize yourself with the installation procedures suggested to successfully mount your new motor lift.
-
Page 3: Getting Started
GETTING STARTED Here is a Parts List followed by a list of the tools, equipment, hardware & supplies that you will need: PARTS LIST [1] Motor Lift [2] Pump relay harness [3] Relays (2) [4] Rocker switch assembly with wiring harness [5] Spacer Block (Shim) [6] Manual [7] Safety Cable... -
Page 4: Before Starting
BEFORE STARTING Selecting the Mounting position The Panther Model 45 Motor Lift is designed so that the motor must be mounted near or at the top of the transom. The unit should be mounted so that the prop will have sufficient depth when the motor is lowered into the water. -
Page 5: Mounting The Motor
MOUNTING THE MOTOR Your motor lift bracket is supplied with a plastic 2 X 3 shim to help mount the motor to the bracket. Place the shim on the inside of the motor plate, under the lip, and hold it in place while placing the motor over the top edge of the bracket. - Page 6 Install the two relays into the two sockets of the main pump relay harness. Connect blue and green pump motor connectors coming from motor lift to blue and green connectors of relay harness (shown as Relay Harness Leads above). Use a small amount of dielectric grease with each of the connectors and plug them together.
- Page 7 MOUNTING THE RELAY HARNESS WARNING! Do not connect relay harness to battery until entire assembly and controls are mounted and ready. Severe damage to pump and controls could occur. A. Find suitable place to mount relay harness. A dry place, typically the rear compartment is recommended.
- Page 8 FLUSH MOUNTING ROCKER CONTROL SWITCH NOTE: Mounting surface must be a minimum of 1/16 inches (1.6 mm) or a maximum of ½”. (12.7 mm) thick for toggle control switch assembly to tighten securely. 1. Using a 2-1/8 inch (54 mm) hole saw, drill out marked area of mounting surface. 2.
- Page 9 SURFACE MOUNT ROCKER CONTROL SWITCH 1. Route toggle control switch harness through surface mounting adapter. 2. Mark and drill pilot holes in the mounting surface using 3/31” (2.4mm) drill bit. Route wiring harness though notch in mounting adapter. Secure switch assembly to mounting surface with self tapping screws as shown.
- Page 10 WARNING Personal injury or boat damage could occur if interference exists using the motor lift. Carefully check to make sure that the motor lift and outboard components have adequate clearance in all operation modes. IMPORTANT! Check clearance of all mounting hardware after installation and before water testing.
-
Page 11: Troubleshooting
IMPORTANT NOTE NOT RECOMMENDED Trailering with the motor on the lift is . MarineTech Products will not be held responsible for damages or injuries incurred when trailering with the motor attached to the 55-0045 motor lift. TROUBLE SHOOTING PROBLEM POSSIBLE SOLUTIONS: 1. - Page 12 5. Motor Lift goes in the Check the blue and green wires to be sure they are connected to the the wrong direction same color termination points. Reversing these wires will cause the when operated: motor lift to operate in the wrong direction. 6.
-
Page 13: Available Accessories
AVAILABLE ACCESSORIES Wireless Remote 55-0105* (*Ask for required special adaptor wire P/N 99-0045 pictured below) Control your motor lift from anywhere within the boat without the hassle of tripping over wires. 50ft operating range. Powered from a standard A23 - 12V battery. Can be used on any Panther Trim and Tilt unit or any product that has a two prong molded connector. - Page 14 WIRELESS REMOTE TROUBLE SHOOTING Weak Signal: 1. Battery may be low. To replace battery, remove the screw on the back of the transmitter. Remove the back cover carefully, noticing how the rubber membrane is seated in the case. Remove and replace the battery. Reinstall back cover making sure that the rubber membrane is seated in the case.
- Page 15 The warranty coverage on this equipment is limited to the terms set forth below: CMP Group Ltd. warrants this product to be free of defects in material and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. Positive proof of date of purchase is required for warranty service.
Need help?
Do you have a question about the Panther 55-0045 and is the answer not in the manual?
Questions and answers