HPM D642 Series Instruction Manual

12 Troubleshooting continued
PROBLEM POSSIBLE CAUSE
Your Door Chime has Your Door Chime Receiver batteries
stopped sounding. may be flat (3C batteries).
If the red indicator light on the
Bell Press Transmitter no longer
illuminates when pressed then your
transmitter battery is flat.
If you have checked
Check the distance between your Door
your batteries and your Chime and Bell Press, they may be
Door Chime is still not located too far away from each other.
operating...
Your Bell Press may be located too
close to a metal structure or too close
to the ground.
13 Maintenance
The HPM Wireless Door Chime is an example of superior design and craftsmanship. The following
suggestions will help you care for the Door Chime so you can enjoy it for years:
1. Keep the Door Chime dry. If the Door Chime gets wet, wipe it dry immediately. Liquids might contain
minerals that can corrode the electronic circuits.
2. Use and store the Door Chime only in normal temperature environments. Temperature extremes
can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts.
3. Handle the Door Chime gently and carefully. Dropping it can damage the circuit boards and can
cause the door chime to work improperly.
4. Keep the Door Chime away from dust and dirt, which can cause premature wear of parts.
5. Wipe the Door Chime with a damp cloth occasionally to keep it looking new. Do not use harsh
chemicals, cleaning solvents, or strong detergents to clean the chime.
6. Use only fresh batteries of the recommended size and type. Always remove old or weak batteries.
They can leak chemicals that can destroy electronic circuits.
7. Modifying or tampering with the Door Chime's internal components can cause a malfunction and
might invalidate its warranty.
8. Care should be taken when replacing Receiver batteries. Open casing carefully so as not to damage
the internal wiring.
Warranty
HPM Legrand warrants this product for a period of 3 years
from the date of purchase.
These goods come with guarantees that cannot be
excluded under the Australian and New Zealand Consumer
Laws. You are entitled to a replacement or a refund
for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired if the goods fail to be
of acceptable quality and the failure does not amount to a
major failure.
See the Warranty card enclosed with this product for
further details.
SUGGESTED SOLUTION
Replace the batteries in your Door
Chime Receiver (3C batteries).
Replace your Bell Press Transmitter
battery (3LR50-12V).
Relocate the Door Chime Receiver
closer to the Bell Press.
Relocate your Bell Press away from
the metal structure or further away
from the ground.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
HPM Legrand Australia
1300 369 777
www.hpm.com.au
HPM Legrand New Zealand
0800 476 009
www.hpm.co.nz
ABN: 31 000 102 661
Please read all instructions carefully before installation and use.
Specifications
Bell press supply voltage: 12V d.c
Transmission freq
Range:
Receiver battery voltage:
Sound level:
Battery requirement:
Door chime receiver:
Bell press transmitter:
Note: This series of door chimes is not compatible with units
from HPM's D642 and D641/PI series or with D641/BFL.
Box contents
• Bell Press
• Door Chime receiver
• Mounting screws and wall plugs
• Double-sided tape
1 Features
• Operating range up to 70m
• 2 melodies for selection
• Weather resistant bell press
Long Range Wireless
Door Chime
Battery Operated
Cat. D641/BLR, D641/BLRCC
Instruction Manual
433.92MHz
Up to 70m
4.5V d.c
100dB
3 x 'C' batteries (not supplied)
1 x 12V battery (supplied)
2 Typical Applications
• Visitor alert
• Panic button