Download
Share
Print this page
AXIOMET AX-DG2010AF Instruction Manual
  1. Manuals
  2. Brands
  3. AXIOMET Manuals
  4. Inverter
  5. AX-DG2010AF
  6. Instruction manual

AXIOMET AX-DG2010AF Instruction Manual

Function/ arbitrary waveform generator
Hide thumbs

Advertisement

Quick Links

Download this manual
EN : Th is Dat asheet is pr esent ed by t he m anuf act ur er .
Please v isit our websit e f or pr icing and av ailabilit y at
w w w.hest or
e.hu.

Advertisement

loading
Need help?

Need help?

Do you have a question about the AX-DG2010AF and is the answer not in the manual?

Questions and answers

Summary of Contents for AXIOMET AX-DG2010AF

  • Page 1 EN : Th is Dat asheet is pr esent ed by t he m anuf act ur er . Please v isit our websit e f or pr icing and av ailabilit y at w w w.hest or e.hu.
  • Page 2 Function/ Arbitrary Waveform Generator AX-DG2010AF Instruction manual...
  • Page 3 General Safety Summary Carefully read the following safety precautions to avoid person injury and prevent damage to the instrument and any products connected to it. To avoid potential hazards, please use the instrument as specified. Only qualified technician should perform service procedures To Avoid Fire or Personal Injure Use Proper Power Line Use only the special power line of the instrument which approved by local state.
  • Page 4 Keep the surface of the instrument clean and dry. Safety Terms and Symbols Terms used on the instrument. Terms may appear on the instrument: DANGER: Indicates an injury or hazard that may be immediately happen. WARNING: Indicates an injury or hazard that may be not immediately happen. CAUTION: Indicates that a potential damage to the instrument or other property might occur.

  • Page 5: The Front Panel

    The Front Panel The picture above shows AX-DG2010AF front panel composition: 1. Power Key This key is used to turn on/turn off the AX-DG2010AF. When the power key is off, the AX-DG2010AF is under power off state. 2. USB Host AX-DG2010AF supports USB disk of FAT format.
  • Page 6 3. LCD Display AX-DG2010AF has a 320*240 TFT color LCD display, which can display current function menu, parameter settings, system state, promptings and so forth. 4. Channel Switch Key This key is used to switch channel’s display interface. 5. Waveform Option Area Sine ----Sine Waveform Provide sine waveform output and its frequency ranges from 1μHz to 10 MHz...
  • Page 7 Pulse ----Pulse Waveform Provide frequency ranges from 1μHz to 300KHz pulse waveform output. The backlight of the key lights when the key is being chosen. The “Frequency/Period”, “Amplitude/High level”, “Offset/Low level”, “Pulse width/Duty” and “Delay” of the pulse waveform can be adjusted.
  • Page 8 7. Knob It is used to increase (clockwise) or decrease (anticlockwise) current outstanding numerical value when setting parameters. 8. Arrow Keys When using knob to set parameters, it is used to switch the place of numerical value. When inputting a file name, it is used to move the position of cursor. When saving or reading files, it is used to choose a position to save a file or choose a file to be read.
  • Page 9 Sweep Sweep This key is used to generate “sine waveform”, “square waveform”, “sawtooth waveform” and “arbitrary waveform” sweep signals. It supports “Linear” and “Log” two kinds of sweep manners. It supports “Internal”, “External” and “Manual” 3 kinds of trigger source. The backlight of the key lights when the key is being chosen.

  • Page 10: The Back Panel

    Help Help Press this key to obtain build-in help information about the product. The backlight of the key lights when the key is being chosen. 12. Menu Keys Those keys are corresponding one by one to the left menu, press any key to activate corresponding menu.
  • Page 11 AM, FM, PM external modulation signal input port; User Interface AX-DG2010AF can only display one channel’s parameters and waveform. The picture below shows the interface when CH1 choosing sine waveform. The interface will have some difference when current function is different.
  • Page 12 1. Current Function Display current function name. For example: “sine” shows that sine waveform function is being chosen. 2. Channel State CH1 and CH2 display area which shows the current channel’s choosing state. 3. Waveform Display Area It shows each channel’s current waveform. 4.
  • Page 13 6. Offset It shows each channel’s current waveform’s DC offset. After press corresponding Offset menu, use number keys or knob to change the parameter value. 7. Phase It shows each channel’s current waveform’s phase value. After press corresponding Phase menu, use number keys or knob to change the parameter value.