Table of Contents
Advertisement
Erasing all titles and play lists—Erase
all titles
[RAM]
Preparation
≥Press [DVD] to select the DVD drive.
≥Release protection (➡ page 40).
1
While stopped
Press [FUNCTIONS].
2
Press [3, 4, 2, 1] to select "DISC
SETTING" and press [ENTER].
3
Press [3, 4] to select "Erase all
titles" and press [ENTER].
4
Press [2, 1] to select "Yes" and
press [ENTER].
5
Press [2, 1] to select "Start" and
press [ENTER].
A message appears when finished.
6
Press [ENTER].
[Note]
≥Once erased, the recorded contents are lost and cannot be
restored. Make certain before proceeding.
≥Still picture data (JPEG, TIFF) or computer data cannot be erased.
≥Erase does not work if one or more titles are protected.
Erasing all the contents of a disc or
card—Format
[RAM] [SD] [PC]
Preparation
≥Press [DVD] or [SD/PC] to select the drive.
≥Release protection (➡ page 40).
1
While stopped
Press [FUNCTIONS].
2
Press [3, 4, 2, 1] to select "DISC
SETTING" or "CARD SETTING" and
press [ENTER].
3
Press [3, 4] to select "Format disc"
or "Format" and press [ENTER].
4
Press [2, 1] to select "Yes" and
press [ENTER].
5
Press [2, 1] to select "Start" and
press [ENTER].
A message appears when formatting is finished.
6
Press [ENTER].
[Note]
≥Formatting erases all contents (including computer data),
and it cannot be restored. Check carefully before
proceeding. The contents are erased when you format it even if
you have set protection.
≥Do not disconnect the AC power supply cord while
formatting. This can render the disc unusable.
Formatting normally takes a few minutes, however it may take up
to a maximum of 70 minutes ([RAM]).
To exit the screen
Press [RETURN] several times.
To stop formatting
Press [RETURN].
(You can cancel formatting if it takes more than 2 minutes. The disc
or card must be reformatted if you do this.)
≥Formatting cannot be performed on DVD-R or CD-R/RW.
≥When a disc or card has been formatted using this unit, it may not
be possible to use it on any other equipment.
≥You cannot format a Microdrive or mobile hard disk on this unit.
Enabling DVD-R to be played on other
equipment—Finalize
[DVD-R]
Preparation
Press [DVD] to select the DVD drive.
1
While stopped
Press [FUNCTIONS].
2
Press [3, 4, 2, 1] to select "DISC
SETTING" and press [ENTER].
3
Press [3, 4] to select "Select First
play" and press [ENTER].
Press [3, 4] to select "Top Menu" or "Title 1" and press
[ENTER].
You can select whether to show the top menu after finalizing.
Top Menu: The top menu appears first.
Title 1:
The disc content is played without displaying the
top menu.
4
Press [3, 4] to select "Finalize" and
press [ENTER].
1 Press [2, 1] to select "Yes" and press [ENTER].
2 Press [2, 1] to select "Start" and press [ENTER].
A message appears when finalizing is finished.
3 Press [ENTER].
[Note]
After finalizing
≥The disc becomes play-only and you can no longer record
or edit.
≥Titles are divided into about 5-minute
§
This time varies greatly depending on the condition and mode
of recording.
≥There is a pause of several seconds between titles during play.
Do not disconnect the AC power supply cord while
finalizing. This will render the disc unusable.
≥Finalizing takes up to 15 minutes.
≥You cannot finalize DVD-R recorded on other manufacturer's
equipment.
Disc display on this unit
Recording/Editing/Entering name
Play on other players
DVD-R finalized on this unit may not be playable on other players
due to the condition of the recording.
≥Visit Panasonic's homepage for more information about DVDs.
http://www.panasonic.com/playDVD-R
To return to the previous screen
Press [RETURN].
§
chapters.
Before
After
finalizing
finalizing
DVD-R
DVD-V
±
t
t
±
RQT7303
41
Advertisement
Table of Contents
