1. Manuals
  2. Brands
  3. Global Manuals
  4. Sander
  5. G3489
  6. Operating instructions, parts list, warranty, & warranty repair center

Global G3489 Operating Instructions, Parts List, Warranty, & Warranty Repair Center

6” dual action sander
Hide thumbs
1
2
3
4

Advertisement

Table of Contents

Operating Instructions, Parts List, Warranty, & Warranty Repair Center
IMPORTANT! Read carefully before operating this tool. Failure to operate any power tool
properly can result in personal injury and/or property damage!
Free Speed (RPM) .........................10,000
Air pressure (PSI) ...............................90
Hose Size (ID) ................................... 3/8"
Air Inlet (NPT) ................................... 1/4"
1. Always wear approved eye protection.
2. Have throttle in "off" position when connecting to air supply.
3. Disconnect tool before performing service, changing accessories, or when not in use.
4. Always be in a safe working distance from others when using tools.
5. Keep tools clean and oiled for best and safest performance.
6. Follow instructions for lubricating and changing accessories.
7. Do not wear loose fitting clothing and remove watches and rings.
8. Always use proper hose and fittings. Never use quick change couplings attached at tool.
9. Keep proper footing and balance at all times.
10. Never carry tools by the hose. Keep hoses from heat, oil, and sharp edges. Check hoses
for weak or worn condition before each use, making certain that all connections are
secure.
Lubricate the tool daily with a good grade of air tool oil. The oil can be applied directly into
the air inlet of the tool and then run the tool. A rust inhibitor oil is acceptable for air tools.
Tools of this class operate on a wide range of air pressure. It is recommended that air
pressure of these tools measure 90 PSI at the tool while running free. Higher pressure and
unclean air will shorten the tool's life and may create a hazardous condition.
Water in the airline will cause damage to the tool. Ensure that the air tank is drained daily
Clean the air inlet filter screen on at least a weekly basis. The recommended hookup
procedure can be viewed in the illustration below.
Model # G3489
6" Dual Action Sander
Disc Size .................................................6"
Avg. Air Consump.(cfm)...................... 4
Overall Length ................................... 9-1/2"
Weight (Lbs) ......................................... 4

Safety

Lubrication

Air Supply

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G3489 and is the answer not in the manual?

Questions and answers

Related Manuals for Global G3489

Summary of Contents for Global G3489

  • Page 1 Model # G3489 6” Dual Action Sander Operating Instructions, Parts List, Warranty, & Warranty Repair Center IMPORTANT! Read carefully before operating this tool. Failure to operate any power tool properly can result in personal injury and/or property damage! Free Speed (RPM) ………………..…..10,000 Disc Size ………………………………………….6”...
  • Page 2 The air inlet, used for connecting air supply, has standard 1/4” NPT American Thread. Line pressure should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 1/4” I.D. and fittings should have the same inside dimensions.
  • Page 3 Model # G3489 6” Dual Action Sander Part No. Description Part No. Description 101001-5 5" Foam Pad 101031 Rotor Screw (4) 101001-6 6" Foam Pad/Velcro 101032 Cap Screw 101002 Cap Screw 101033 Throttle Spring 101004 Balance Nut R-S056 Retaining Ring...
  • Page 4 One Year Limited Warranty GLOBAL Industrial air tools carry a limited 1 year warranty to be free from defects in material and workmanship for one year from date of purchase. We will repair or replace at our discretion any defective part or unit which proves to be defective in material or workmanship during this 1 year period.

Table of Contents