Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Airspan AIRVELOCITY 2700
- Page 1 4 T 4 R I N D O O R A D I O N I T Installation Guide Document Part Number: DUG01251 Document Revision: A3 Published: April 2021 © Copyright by Airspan Networks Ltd., 2021. All rights reserved worldwide.
- Page 2 Airspan Networks Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or specifications. Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every care has been taken in preparing these documents. However, Airspan Networks Ltd. does not make any representations and gives no warranties of whatever nature in respect of these documents, including without limitation, the accuracy or completeness of any information, facts and/or opinions contained therein.
-
Page 3: Table Of Contents
Getting Started ........................ 7 AirVelocity 2700 Job Sheet ..................... 7 Verifying Prerequisites ....................8 Verifying Site Requirements ................... 8 Verify Installation Requirements ..................8 AirVelocity 2700 5G Sub-6 Installation ................ 11 Ceiling Mount ........................11 Wall Mount........................17 Cable Connections ......................18 LED Display ........................19 Job Sheet ...................... - Page 4 4T4R Indoor Radio Unit – Installation Guide IGURES Figure 1: AirVelocity 2700 5G ........................6 Figure 2: AirVelocity 2700 5G Sub-6 Physical Dimensions ............... 10 Figure 3: Assemble Ceiling Clip ........................11 Figure 4: Attaching the Ceiling Clip to the Mounting Bracket ..............11 Figure 5: Assemble the Mounting Bracket with the Clip onto the Keel/T-bar ........
-
Page 5: Document Information
This document details procedures for installing the Airspan’s AirVelocity 2700 5G Sub-6Hz, RU aimed as part of the 5G NR standard and its place in the Airspan product suite. This document is intended for qualified personnel with a working knowledge of 5G. -
Page 6: Warnings And Cautions
4T4R Indoor Radio Unit – Installation Guide Warnings and Cautions Human Exposure to Radio Frequencies The AirVelocity 2700 5G Sub-6 should be operated from a minimum safe distance of 20 cm (7.87 in.) during normal operation. Radio Interference The AirVelocity 2700 5G Sub-6 generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. -
Page 7: General
Failure to do so may void Airspan's product warranty and may expose the end user or the service provider to legal and financial liabilities. Airspan and its resellers or distributors are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas. -
Page 8: Adherence To European Directive 2014/53/Eu
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations 1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to ensure that the product is disposed of in conformance with the relevant regulatory requirements. -
Page 9: About This Document
Connect power Intended Audience This guide is intended for persons who are responsible for installing the AirVelocity 2700 5G Sub-6. These persons should have a working knowledge of the equipment. Document Conventions This document uses the following typographic conventions. -
Page 10: Introduction
1.1 AirVelocity 2700 5G Sub-6Hz The AirVelocity 2700 RU is a Radio Unit (RU) for 5G Radio Access Network (RAN). It is combined with additional RAN elements in order to provide a complete 5G mobile radio communication system. The AirVelocity 2700 is based on open interfaces as defined by the O-RAN alliance. The fronthaul interface between the AirVelocity 2700 and the DU complies with RAN split 7.2a and includes the... -
Page 11: Getting Started
4T4R Indoor Radio Unit – Installation Guide 2 Getting Started 2.1 AirVelocity 2700 Job Sheet Plan the installation of the AirVelocity 2700 by using the Job Sheet, which you can find as a removable job aid in Appendix A for this guide. -
Page 12: Verifying Prerequisites
AirVelocity 2700 5G Sub-6Hz 4T4R Indoor Radio Unit – Installation Guide 3 Verifying Prerequisites Prior to installing the AirVelocity 2700 5G Sub-6Hz, verify the required safety, power, tools, parts and components. This chapter includes the hardware, software, and client requirements for installation. ... - Page 13 DC Power Supply – Plug Type A (JP) Depending on field conditions, either a suspended ceiling or standard ceiling mounting kit is required, which is included in the packaging. © Copyright Airspan Networks Ltd., 2021 P/N: DUG01251 Rev. A3, Apr 2021...
-
Page 14: Figure 2: Airvelocity 2700 5G Sub-6 Physical Dimensions
AirVelocity 2700 5G Sub-6Hz 4T4R Indoor Radio Unit – Installation Guide 3.2.3 Physical Dimensions AirVelocity 2700 5G Sub-6 is in an indoor enclosure. Table 4: AirVelocity 2700 5G Sub-6 Physical Dimensions Dimensions (H x W x D) Volume Weight 225 x 225 x 44mm / 8.8 x 8.8 x 1.7”... -
Page 15: Airvelocity 2700 5G Sub-6 Installation
Ceiling Clip – used for mounting on a suspended ceiling – provided with screws, (M3x 6mm x5), (M3x6 for locking). 4.1 Ceiling Mount The following defines the AirVelocity 2700 ceiling mount assembly procedure for a suspended ceiling and a conventional ceiling. ... -
Page 16: Figure 5: Assemble The Mounting Bracket With The Clip Onto The Keel/T-Bar
5. Slide together the clip onto the suspended ceiling’s T-bar, as shown below: Figure 6: Tighten Clip to T-bar 6. Fasten the clip with the 4 – M3x6 screws, as shown below: Figure 7: Tighten the Screws © Copyright Airspan Networks Ltd., 2021 P/N: DUG01251 Rev. A3, Apr 2021... -
Page 17: Figure 8: View From The Bottom
AirVelocity 2700 5G Sub-6Hz 4T4R Indoor Radio Unit – Installation Guide 7. Lift the AirVelocity 2700 5G Sub-6 into position and align the mounting screws (supplied) into the key-holes on the underside of the mounting bracket, as shown below: 8. Slide unit to engage the key-hole slots. -
Page 18: Figure 10: Install Security Lock
Fiber Ethernet port – SFP+ 10GbE – if applicable Copper Ethernet port – ETH 10GbE – if applicable Connect to power using a Phoenix Type Connector 2-Pole 5mm Pitch – (input range 42- 57vDC) © Copyright Airspan Networks Ltd., 2021 P/N: DUG01251 Rev. A3, Apr 2021... -
Page 19: Figure 11: Hole Spacing For Mounting Bracket
Use appropriate ceiling hardware according to field conditions. 7. Lift the AirVelocity 2700 into position and align the mounting screws (supplied) into the key- holes on the underside of the mounting bracket, as shown below: ©... -
Page 20: Figure 13: Mounting Airvelocity Unit On The Mounting Bracket
Fiber Ethernet port – SFP+ 10GbE – if applicable Copper Ethernet port – ETH 10GbE – if applicable Connect to power using a Phoenix Type Connector 2-Pole 5mm Pitch – (input range 42- 57vDC) © Copyright Airspan Networks Ltd., 2021 P/N: DUG01251 Rev. A3, Apr 2021... -
Page 21: Wall Mount
Drill the four (4) holes. After drilling insert wall plugs (x4) (not included). Wall plugs (x4) and necessary hardware are not supplied by Airspan and are the responsibility of the installer. Use appropriate wall plugs according to field conditions. -
Page 22: Cable Connections
Secure the wires by tightening the retention screws, as shown in figure below. 4.3.2 Fiber Ethernet (SFP+) Cable Connection Insert SFP+ module and connector (when applicable), as shown in figure below. © Copyright Airspan Networks Ltd., 2021 P/N: DUG01251 Rev. A3, Apr 2021... -
Page 23: Led Display
Flash Once Startup Ongoing Hardware Error Clock Locking Blink@1HZ Clock Locked STATUS Power On Flash Once Flash Once Fronthaul Interface Linkdown Connect Blink@1HZ Normal Operating eCPRI Packet Error Blink@1HZ © Copyright Airspan Networks Ltd., 2021 P/N: DUG01251 Rev. A3, Apr 2021... -
Page 24: Job Sheet
4T4R Indoor Radio Unit – Installation Guide Job Sheet This job sheet enables the users to keep track of their installation. It covers all the prerequisites required for accomplishing the AirVelocity 2700 installation. Table 7: Job Sheet Site Requirements ... -
Page 25: Acronyms, Abbreviations, And Definitions
4T4R Indoor Radio Unit – Installation Guide Table 8: Acronyms, Abbreviations, and Definitions Term Expansion Light Emitting Diode New Radio Long Term Evolution Radio Unit User Equipment. The end user in 5G © Copyright Airspan Networks Ltd., 2021 P/N: DUG01251 Rev. A3, Apr 2021... -
Page 26: Customer Service Help Desk
Customer Service Help Desk Airspan’s Customer Care Help Desk offers prompt and efficient customer support services. To take advantage of Airspan’s Customer Care Help Desk support, you must be a registered user and must have a valid support contract. To register, click... - Page 27 Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Need help?
Do you have a question about the AIRVELOCITY 2700 and is the answer not in the manual?
Questions and answers