Panasonic Viera TC-46PGT24 Operating Instructions Manual page 24

Viewing 3D images on TV
Using the television menu controls, set so that 3D images are shown.
You can watch 3D images in the following cases: (2D->3D (Simulated 3D) p. 62)
• When a 3D image supporting Blu-ray Disc is played on a 3D image supporting player/recorder connected using a
HDMI cable to a 3D image supporting television.
• 3D image supported broadcast (program)
• 3D Photo, 3D Movie taken by LUMIX / Camcorder. (available in autumn 2010)
Press to exit from a
menu screen
Press to return
to the previous
screen
If the images cause discomfort, they can be adjusted with the following settings.
Off: 3D images can be deactivated by turning "Off"
Auto detect: (Default) When the HDMI receives
3D
settings
Side by side/Top and bottom:
2D->3D: Allows you to transform normal 2D image to
Native: Displays the input signals as is on the screen.
When the HDMI receives information in which Full HD (Frame
Sequential Method) is detected, the image is automatically
displayed regardless of "3D format" settings.
* If a signal received from an external device is different from the 3D setting of the TV, such as 2D signal when the TV is set to
24
3D mode, the images may not be displayed correctly.
Wearing the 3D Eyewear
Press and hold the power button on the 3D Eyewear for approximately 1 second.
(The Indicator lamp lights for approximately 2 seconds.)
Put on the 3D Eyewear.
If the 3D Eyewear slips out of place, hold it in place using the specialized band,
and adjust the length of the band. (p. 23)
If the 3D images are not displayed correctly or the images cause discomfort, the
images can be adjusted by following this procedure.
* The perceived three dimensional effects of the 3D Eyewear differ from person to person.
Display the VIERA TOOLS
screen and select "3D"
Using Setup menu (p. 39)
After Use
Press and hold the power button on the 3D Eyewear for approximately 1 second.
(The Indicator lamp on the 3D Eyewear flashes 3 times, then the power switches off.)
After using the 3D Eyewear, store it in the case provided.
These settings are reset by switching inputs or selecting channel. (Settings will not be retained.)
3D Eyewear (On/Off)
On
3D Eyewear
while viewing. (When 3D Eyewear is not worn)
3D format
(Auto detect/Side by side/Top and bottom/2D->3D/Native)
3D format Auto detect
information in which 3D mode is detected, 3D images
are automatically displayed according to the signal.
(Switching may not occur depending on the signal.)
Allows you to set this setting to match the image state.
3D image (p. 62).
You can also adjust 3D depth in "2D->3D depth"
menu. (see right)
"Left / Right swap" and "Diagonal line filter" are not available.
Viewing 3D images
select
next
On: Resolves discomfort caused by receiving a
(Continued)
Select the item and set
3D settings (see below)
3D settings
3D Eyewear On
Auto detect
3D format
2D->3D depth Medium
Swapped
Left / Right swap
Off
Diagonal line filter
Safety precautions
2D->3D depth (Minimum/Medium/Maximum)
2D->3D depth Medium
Adjusts 3D depth. Available only when
"2D->3D" is selected in "3D format".
Left / Right swap (Normal/Swapped)
Swapped
Left / Right swap
Change this to "Swapped" when the phases are
reversed (when there is an unusual sense of depth).
Diagonal line filter (On/Off)
(Switch "Side by side" and "Top and bottom" types)
Off
Diagonal line filter
quincunx matrix signal.
Safety precautions
Displays message for viewing 3D images.
select
change