Ortech LEDFP-52BIF Instruction Manual

Fireplaces
MODEL LEDFP-52BIF | LEDFP-72BIF
• NEVER leave this fireplace unattended
• Connect to properly grounded outlets only
•
ALWAYS unplug the fireplace when not in use
• This fireplace is hot when in use. To avoid burns, DO NOT let bare skin touch hot
surfaces. If provided, use handles when moving this fireplace
•
FOR RESIDENTIAL USE ONLY — This fireplace is NOT for commercial use. Any
commercial or public use of this fireplace voids all warranties as well as could
cause injury and damage to property
• Extreme caution is necessary when any fireplace is used by or near children or
invalids and whenever the fireplace is left operating and unattended
•
DO NOT operate any fireplace with a damaged cord or plug or after the fireplace
malfunctions, has been dropped or damaged in any manner. Discard the
fireplace, or return to authorized service facility for examination and/or repair
•
DO NOT run power cord under carpeting. DO NOT cover power cord with throw
rugs, runners, or similar coverings. DO NOT route power cord under furniture or
appliances. Arrange power cord where it will not be tripped over
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust
openings, as this may cause electric shock or fire, or damage to the fireplace
•
To prevent a possible fire, DO NOT block air intakes or exhaust in any manner.
Doing so could cause a fire. DO NOT use on soft surface, like a bed, where
openings may become blocked
• This fireplace is not intended to be a primary heat source. It is for supplemental
heat only. INDOOR and OUTDOOR use
•
ALWAYS disconnect this unit from the power supply before performing any
assembly or cleaning, or before relocating the electric fireplace
• ALWAYS check your fireplace cord and plug connections with each use:
1) Make sure the plug fits tight in the outlet. Faulty wall outlet connections or
i) loose plugs can cause the outlet to overheat
2) Fireplaces draw more current than small appliances. Overheating may occur
2) even if it has not occurred with the use of other appliances
3) If the outlet or face plate is hot, discontinue use immediately and have a
3) qualified electrician inspect and/or replace the faulty outlets
• Check the parts list to make sure nothing is missing. Dispose of packaging
materials properly. Please recycle whenever possible
• Tools required (not included) are: Phillips screwdriver, stud finder, level; tape
measure, electric drill; 1/4" wood drill bit, and a hammer
AUTION
CAUTION
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES. Electrical products can cause
death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician.
PARTS & HARDWARE
Fireplace
info@ortechindustries.com
www.ortechindustries.com
WARNING
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.
1. DO NOT open any panels
2. NEVER immerse in water or spray with water
3. Turn OFF the appliance completely and let cool before servicing
4. Only a qualified service person should service and repair this electric fireplace
A p p l i c a t i o n
Drywall anchors
Wood Screw
13376 Comber Way
Surrey BC V3W 5V9
N o t i c e
•
A fireplace has hot and arcing or sparking parts inside. DO NOT use it in
areas where gasoline, paint, or flammable liquids are used or stored
• Use this fireplace only as described in this manual.
Any other use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons
• Only use this fireplace on a 120V AC 10 amps grounded circuit. NEVER
overload the circuit. If this fireplace trips the circuit breaker, unplug all
other appliances on the same circuit before the next use. Avoid plugging
other appliances into the same circuit as this fireplace
• To prevent a possible fire, DO NOT block air intakes or exhaust in any
manner. Doing so could cause a fire. DO NOT use on soft surfaces, like a
bed, where openings may become blocked
• NEVER hang this unit on a wall directly below an electrical outlet or
permanently install in a recessed area of the wall
• Avoid fire — regularly inspect all air vents to make sure they are free
from dust, lint or other blockage. Unplug the unit and clean with a
vacuum only. DO NOT rinse or get it wet
• ALWAYS mount to wall bracket before use. DO NOT set on the floor, or
other surface, to use. NEVER use a wall mount bracket from another
manufacturer
• Risk of electric shock — DO NOT open. No user-serviceable parts inside
•
ALWAYS turn the fireplace off before unplugging it from the outlet
• NEVER plug this fireplace into an outlet that is old, cracked, or has any
loose wires or connections. Plugging this fireplace into a faulty outlet
could result in electric arcing within the outlet that could cause the outlet
to overheat or catch fire
•
The power cord supplied with the fireplace has three prongs:
two flat blades (LIVE and NEUTRAL) and one round pin (GROUND). If a
3-slot receptacle is not available, an adapter MUST be used. The adapter
MUST be PROPERLY GROUNDED to the outlet box (see Fig. A).
Adapter is not included.
•
This product includes a GLASS panel. Always use extreme caution when
handling glass. Failure to do so could result in personal injury or property
damage. Remove all parts and hardware from the carton and place them
on a clean soft dry surface. Parts and assembly steps are grouped for
wall-hanging or recessing use.
Remote Control
375 Admiral Blvd
Mississauga ,
ON L5T 2N1
Instruction Manual
Crystals Drift Log Piece
1-888-543-6473
1-888-541-6474