Advertisement
Make sure that the inserted tool or accessory is mounted correctly, if not it may cause high speed projectiles.
Make sure that no dangerous circumstances can occur for other persons in the work area.
Always wear safety glasses during operation of the tool. The grade of protection must be in relation to the risk of the operation.
Rotating mounted accessories can be easily entangled by rubber coated or metal reinforced gloves. Wear suitable gloves.
Keep fingers out of reach of the inserted tool or accessory.
Never hold the drive shaft, socket, bit, inserted/mounted tool/accessory with your hands while rotating.
For impact and impulse wrenches: Only use impact sockets, see our Action catalogue.
The use of safety-/working gloves is recommended.
Use ear protection as instructed by your employer or as required by occupational health and safety requirements.
Reasonable countermeasures have to be taken to keep the noise level as low as possible.
Always check that the mounted tool or accessory is not damaged. Breakage and flying fragments can cause injuries.
Keep rotating parts out of reach of any body part.
In case of long hair, wear a hairnet otherwise it can be trapped causing injuries.
Never wear loose clothing, wear suitable clothing otherwise it can be trapped causing injuries.
Only use accessories for this tool that are designated for this tool by its manufacturer.
Convince yourself that no persons are in the working zone or danger zone.
The advised minimum age for operating this tool is 18 years.
This tool is not intended for use in potential hazardous areas and is not insulated from coming into contact with electric power.
Wear the appropriate clothing to feel comfortable at the workplace.
On overhead work, use safety helmet.
Due to the process, the work piece, inserted/mounted tool/accessory may get hot causing burning injuries: Be aware of this.
Never let the tool run free in the air: the accessory may come loose and become a projectile causing danger or injury
O nly use accessories that are in good condition, worn accessories can be dangerous and cause injuries.
O nly trained and qualified operators should use the tool.
N ever use a damaged tool.
Tools shall be inspected periodically to verify that the ratings and markings required by the applicable part of the ISO 11148 series are
legibly marked on the tool. If not the user/employer shall obtain replacement labels from the dealer or manufacturer.
U se only tight fitting gloves, loose gloves can be trapped or entangled causing injuries.
Use the specified gloves for the application that protects against: heat, cold, entanglement, cutting, impacting
Do not wear any shawls jewelry etc that can be trapped or entangled causing injuries.
I n case of power loss, release the trigger immediate.
M ake the possible countermeasures to minimize noise emission: if possible, use silence materials on the workpiece or walls around the
work station.
A risk assessment related to the noise emission on at the work station on the work piece has to be made to determine the correct ear
protection according health and safety regulation.
A risk assessment related to the vibration exposure to determine the maximum working hours per day for the operator. Vibration can
cause damage to blood vanes and nerves (white finger disease). Hold the tool with light but safe grip, higher grip force can increase
vibration effects.
Electrical Safety
This product is for the indoor exclusive use. Do not use it in rain, in a damp place and a wet place. Moreover, never use it in the place
with the fear of the ignition and the explosion, because those are hazardous situation.
Do not move by holding the power cord. Do not pull the cord to remove the plug from the socket-outlet.
Avoid damage of cord due to stepping, entangling, or unreasonable force, a damaged cable must be replaced immediate.
A void pinching of power cord in the object to be tightened or surrounding facility in the tool operation and avoid the contact with
rotating parts. The power cord may be damaged and it may results in accident.
U se the battery charger at rated supply voltage (AC 100-240 V).
D o not use DC power supply, engine generator, or power transformer.
K eep away from sources generating large electromagnetic noise, such as welder, DC brush motor.
Be sure to use the provided power supply cord. Use of other power supply cord may cause malfunction, heat generation, or fire.
B e sure to fully insert the power plug. Failure to do so may result in electric shock or fire due to heat generation.
I f you do not use the product, unplug from the receptacle.
W ipe out dust or stain accumulated on the power plug or receptacle with a dry cloth. Failure to do so may result in electric shock or
fire.
D o not insert or remove the power plug from the receptacle with wet hand. Doing so may result in electric shock.
N ever disassemble or modify the charger.
Battery Safety
Do not disassemble or modify the battery pack and battery charger, doing so may result in heat generation, fire, electric shock, or
injury.
D o not throw the battery pack into fire or heat it, doing so may result in rupture or release of hazardous substances.
D o not drive a nail or give an impact such as fall on the battery pack or battery charger. Doing so may result in heat generation, fire,
electric shock, and/or injury.
Advertisement
