Getting Started; Operation - Honeywell HPA060 Series Owner's Manual

GETTING STARTED

• Select a firm, level, and flat location.
• When operating, large volumes of air are drawn toward the air purifier. Surrounding areas should be cleaned
and/or vacuumed frequently to prevent build-up of dust and other contaminants. This may also help prolong
the life of the filter. If the unit is placed on a light colored carpet, a small mat or rug should be used underneath
to prevent staining. This is especially important in homes with contamination from smoking, fireplaces, or
where candles are burned.
• Ensure the front of the unit faces away from the closest wall or furniture.
• Ensure no grilles are blocked.
INSTALL CERTIFIED HEPA FILTERS AND ODOR REDUCING PRE-FILTER
The Certified HEPA Filters are supplied within the air purifier. They are wrapped to ensure
purity, and are labeled to help identify the proper replacement filter
• Before using your new air purifier you must remove the wrapper covering the filter(s).
Make sure the air purifier is OFF and unplugged. While pressing on the tab at the top
of the rear grille, pull the grille towards you and remove it from the unit and set it aside
(See Fig. 2). Grasp the sides of each filter frame near its top end and pull outward.
Repeat for the second filter if applicable.
• Remove protective wrap from the filter(s).
• Place the HEPA Filter(s) into the air purifier housing with the arrows pointing toward
the unit. Insert the bottom edge of the filter frame and press the top of the filter down
and inward until the filter is firmly in place. Repeat for the second filter if applicable.
Install the Household Gas & Odor Reducing Pre-Filter that is supplied within the air purifier.
It will be wrapped in plastic wrap to keep it fresh
• Remove the pre-filter from the protective plastic bag.
• Secure the pre-filter under the pre-filter clips on the inside of the rear grille.
• Replace the rear grille by lining up the tab at the bottom of the grille with the slot in the air purifier.
Push the top of the grille towards the unit until it snaps in place. Snap the filter grille back into place.

OPERATION

The energy efficiency of this ENERGY STAR certified model is measured based on a ratio between the model's
CADR for Smoke and the electrical energy it consumes, or CADR/Watt.
Fig. 2
H .
Filter
+ .
B
Pre-Filter
4
OPERATION (Cont.)
Portable air purifiers are more effective in rooms where all doors and windows are closed. It is recommended
that you run your air purifier while you are at home to help clean the air.
HPA060 Series Operation:
• Once you have removed the protective wrappers from the filters and have
installed them in the unit, ensure the air purifier's control knob is turned to
the OFF postion and plug the power cord into a working outlet.
• Select desired cleaning level by turning knob to Low, Medium, or High
setting (Fig. 3).
Model HPA160 Series Operation:
• Once you have removed the protective wrappers from the filters and
have installed them in the unit, plug the power cord into a working
electrical outlet.
• Select cleaning level by simply TAPPING the power icon (
through setting options. The blue LED will illuminate the selected
setting. TAPPING the Power button will also shut the unit OFF after moving through the cleaning settings.
HPA160 Series models have a Turbo Setting option. (Not available on the
HPA060 Series):
To select the Turbo setting, push the Turbo button (
illuminate (Fig. 4). Push the Turbo button again and the air purifier will
return to the previously selected cleaning level.
Using the Timer Option (Not available on the HPA060 Series):
The HPA160 series models also have an Automatic Shut-off Timer
option. If you would like the unit to automatically shut off after a specific
period of time, push the Timer button ( ) and toggle through
to select 2, 4, or 8 hours. The air purifier will automatically shut off after
the selected time period.
• To set the unit for Automatic Shut Off, push the Auto-off Timer icon (
• Continue to push the timer button to toggle through to the desired time setting.
• An LED will illuminate under the hour setting to indicate the selected run time.
• The unit will automatically shut off after the indicated run time.
) to toggle
Fig. 3 HPA060 Control Panel
). The Turbo LED will
Fig. 4 HPA160 Control Panel
).
5